25370409612 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from North Tonawanda, NY
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat when drying
Replaced thermo-fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G V from Bowie, MD
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No ice - Replace water valve
TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gaylord from Riverside, CA
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Ice cubes were half the normal size to none at all
Remove back cover (5 screws )remove valve ( 1 screw ).Disconnect in and out water lines. Disconnect wire on solenoid. Install in reverse. Dont forget to turn off water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from Olton, TX
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
valve busted
I took 2 screws loose and undone water lines, replaced and reconnected everything. Real easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from New York, NY
- Parts Used:
- 240535201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
This was so simple - no tools needed
Find part # on broken shelf holder, enter into google search, this site pops up. Selected correct part, paid, waited for delivery, open box, slide part out and then slip it into the groves. So simple. I'll recommend this site any chance I get.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Woodstock, GA
- Parts Used:
- 242252603
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Valve nut stripped
Old part threads : made in China (brass) New part : made in Mexico (steel). First, unplugged it from the wall. As for the valve, removed the two screws holding the valve in, disconnected the plug, took the pipe cutter, cut the blue line to the ice maker, cleaned up the cut, pushed that line into the new one and reassembled. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Boise, ID
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench set
Ice maker no working
Removed water line. Removed two screws holding valve. Disconnected line from valve going to Ice maker. Replaced screws and water line. Most important thing in working with Parts Select was the information they provided when I called them. I had called electrolux and was given no information and was told they would send out a repairman at which point I told them to get lost. Cost of part $30.00 vs service call of $75.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Springfield, OR
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer door sagging due to warped hinge
Just block the door up so it doesn't fall off, remove the two screws, replace hinge, and replace screws. My wife could have done it. Metal replacement part is much better than the original plastic that warped from day one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Chesaning, MI
- Parts Used:
- 240313703, 5304507146
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer door sagged & didn't seal properly
Installed Metal hinge(old hinge was plastic) to take out sag of door.(painted the hinge color of refrigerator as hinge doesn't have plastic appearance cover )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James M from Charlotte, NC
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replacing a freezer door rack
It was a perfect fit and snapped into place in seconds. No instructions were required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Norman, OK
- Parts Used:
- 240364503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The crisper pan cracked
I took the cracked pan out, waited for the new pan to arrive (2 days) and slid the new pan right in. It was so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from EL PASO, TX
- Parts Used:
- 240535201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Rack
No tools were required to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Apache Junction, AZ
- Parts Used:
- 241554901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Light Would Not Come On.
I removed the four bolts holding the light switch and temp knob with a nut driver, unplugged the unit and moved it to the table top. I removed the switch and replaced it with a new one. I plugged the unit back in and drove the four screws in with a nut driver and the light now comes on when I open the door. Real simple!
Was this instruction helpful to you?
Thank you for voting!