25352339201 Kenmore Refrigerator - Instructions

Removed the plastic water tubes cover with a nut driver. Disconnected water hoses. Dropped control box assembly with nut driver. Removed old filter base with phillips screwdriver. Assembly opposite.

Took off Door on Refr. and unscrewed Doorstop,
removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes
including reattaching Door. A 10 year old can do it.

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

I worked for GM as a Frigidaire Tech, before starting my own business. I have retired now.
I took the three screws off the back of the bracket holding the motor. Disconected wire harness and pulled out the motor. Reverse to install. servantoftheking@hughes.net

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

The repair was very easy. I loosened the two screws holding the icemaker onto the side of the freezer, then unplugged the icemaker. Reversed the order, and it was done. You have to shut the water off first.

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

Remove shelves and rear panels to get to motor. Motor is held in place on shroud by simple strap. Remove fan blade, then un hook strap, remove and save rubber spacers on old motor to reuse to remount new motor. New motor Mew motor has wiring harness that is universal. Cut out the three wires that go to the new motor leaving long as possible, cut wires from old motor as long as possible, strip ends of all wires 1/2 inch, connect wires by color,slip into provided wire connectors and crimp. Pull on wires to insure connection. Tie wires together so they don't touch the coils. Plug in and check operation. If all is working unplug and replace all covers and shelves. Plug back in and it will take few hours to reach operating temperature. Video of side by side repair shows easy removal of panels and motor.

First I unplugged the refrigerator.
Then I removed the drip tray to gain access to the three screws that supported the module cover. The three screws were rusted into place and required a square No. 1 bit to remove. Once I finally found the right bit that fit, with much effort, I removed the three rusted screws and the module being careful to unplug the circuit board cable from the module back.
I used a NON magnetic screwdriver to remove the 4 screws that held the circuit board on the back of the module cover. I removed the cover, power board, carrier and light module and put it on the new module cover I also bought (because it was broke due to the rusting of the screws). I made sure I stayed in full contact with the circuit board and module cover at the same time to avoid static discharge from the new board from the static wrapper to the module cover because static discharge may damage the fragile microchips in the new board.
Once the pieces were in place, I put back on the back cover and 4 screws with a NON magnetic screwdriver.
I pealed the Module cover lable off the old cover and pressed it on the new module cover. (A new sticker cover cost more than a circuit board).
I reattached the circuit board cable and replaced the module. I screwed in three new phillip screws and placed back in the drip tray.
I plugged in the refrigerator and no more problem with the Ice and water maker being intermitten.

Looked at video on how to remove and reinstall support and followed the instruct ions

Replaced the Triple Water Valve

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.