36369967991 Kenmore Refrigerator - Instructions

Found the part I needed in only a few minutes on the website and ordered it in less than 5 minutes. The part came within 2 days and I simply removed 2 screwes from the old part and installed the new part and replaced the 2 screws , the easiest repair job that I have ever done in my home. Thanks

Start at the inside top corner and slowly work across the top, pushing with thumbs so that you feel it fitting into the groove. Go inch by inch. No speeding on this one. The gasket was so well packed that there were no folds or kinks, so no heating was necessary.

Wow, end result was amazing. I had to place my ear close to the refrigerator to find out if the fan was working. So quiet. Prior to this we could hear it in the bedroom. I replaced the fan motor, blade, grommets, i.e. the whole fan train. There were two screws holding the fan which were removed. (After removing the back panel.) Then removed the old blade and dust cap. Detached the wiring harness at the junction. Then reassemble in the reverse order. I screwed up the 1st time...installed the front motor grommet in reverse. Fan blade was not centered. Resulted in a few mins rework. Actually spent more time cleaning all the dust from the compartment and behind the refer than it took to install the new fan system. Did I say that I couldn't be more pleased with the no noise result?

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

Slid old end cap off, slid new end cap onto retainer bar and reinstalled. Probably the easiest repair I've ever done.

I just let the gasket sit on a flat surface for a couple of days. I didn't immerse it in hot water as the directions stated. It went on fairly easy. Just took a bit of patience. The fact that it was packaged nicely without it being jammed into a tight bundle probably was a big factor in the ease of installation.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

I first unscrewed the broken right rail from the back piece and replaced with the new rail. Did the same for the left piece side. Attaching to the front rail was challenging because I took a while to figure out how to remove the cover (where the pictures of the vegetables/fruits are). But if you just get a narrow flat-head screwdriver under there, it just pries off. Then you can get to the little screw that attaches the side rails to the front piece.

After finding your web site, the description of my problem was pretty clearly referenced as to what parts where the likely problem. When I received the parts it was only a matter of unplugging the refrigerator, removing the cover in the freezer and cutting and stripping the two color coded wires for the thermostat and wire nutting the wires and putting wire tape on them. Then put the coil cover back on. Then in the refrigerator section, remove the controls cover and then take the controls compartment loose and unfasten the old defrost control, and install the new one. Then put every thing back in place. Plug the refrigerator back up and set the temperature to medium.

replaced lights in refrigirator and freezer

I removed the Glass Shelf on top of the Vegetable Drawer assembly, unfastened the front rail from the broken slide rail and removed the entire assembly. I cleaned the parts and then installed the new rail. I placed the drawers in the repaired assembly and placed in the refridgerator. It really went well. I didn't need the other parts order. I only had them just in case they were needed.

I removed the old gasket and snapped the new one into the grooves. No tools were required.

PartSelect provided excellent service. It was a GE manufactured part. GE no longer stocked this part.

PartSelect is a terrific appliance repair parts vendor.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.