25358085899 Kenmore Refrigerator - Instructions

Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.

Ice was not dispensing. Examined the ice bin and auger, noted that the plastic ring that holds the auger at the front of the bin was broken all the way around. Pulled out old bin, making sure the ice fill level was raised all the way up, and pushed in the new bin. The new bin filled with ice, which promptly turned into a solid mass of ice because the ice maker was also faulty. I replaced that as well and have not had any issues.

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

It was a snap. Literally. all I had to do was snap and slide the front off the broken drawer and slide and snap it onto the new.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

I ordered a replacement on-line (real simple, visual aids helped more than model nos). Once I received it in the mail, I installed it (no tools required) and now my water filter and ice maker are back to doing what they do best!

take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.

Found that that ice maker was working mechanically and electrically but was not receiving water to the ice maker. I found that the dual solenoid valve was not sending water to the ice maker when I asked for water so I ordered a new dual solenoid and this fixed the problem,however I also found the water feed tube was frozen and had to take it off an thaw it out. Now the ice maker and water dispenser is working great.

Removed outside cover on door despencer, (4 screws) unplug wire, removed unit from refrig and replace rusted thru wire that holds door shut. It was fairly easy. I actually took it apart twice, once for diagnosis and once for repair after the part arrived.

The part’s picture on the site was not identical to the part delivered, but the function was essentially the same. It had different connectors to the outgoing tubes and a slightly different method of attachment to the refrigerator (it required 1 additional skew - not included). After verifying the part would still work, I shut off the water. Then I disconnected the two outgoing tubes. Made sure I had bucket handy to handle excess water. Then I removed the part using an adjustable wrench (1 screw) and then detached the incoming tube. Attached the incoming tube to the new part and then remounted (2 screws). And then I attached the two outgoing tubes and turned on the water. It works great and I have no plumbing experience.

Jonnine's husband did the repair - At first, I was stumped on the cause of the problem because I thought because I did get some ice, the pump (valve) must be working. But after pulling the dust cover back off the bottom of the fridge, I removed the dual valve. I had my wife operate the switch in the door for water and I could tell that it wasn't activating the valve at all. Ordered the valve, took 30-45 minutes to put it on. Worked like a charm. Full ice bucket now and water through the door again. Easy install.

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.