1068480130 Kenmore Refrigerator - Instructions

new shelf was installed by placing the clips into the provided slots.

Received replacement part the day after placing order. Took broken part out and put new in. It was that simple.

Using a pair of pliers position the nose perpendicular to the inner wall of the ref and grip tight on the flat part of the support stud and twist counterclockwise until it become loose. Once loosened pull the support stud outward until it clears the the hole. Installation: Slide the support stud in and twist it hand tight. Using a vise grip and locking the jaw just tight enough to hold it firm on the flat parallel edges twist them (one at time) clockwise until it feels tight the tongues are parallel to to be able to slide the shelf support.

The Sears man came out and told me it was the thermostat that needed to be replaced and it would cost $321 plus tax. I went on youtube and watched the Partselect video several times and decided to order the part after seeing how easy it was to install. Total cost $65. I put the laptop on the counter and watched it as I installed it. It helped that I could go back and watch a certain part if there was a problem. But I had no problems and installed it in 20 minutes. Very, very simple to do. Of course I had to pay $75 to the Sears man but I saved about $200 . Thanks Partselect.

Exactly how the instructional video described it to be. No surprises what so ever. Ended up not being the culprit to my problem. Ordered and installed a bi-metal defrost timer. Also, extremely easy as the instructional video described it to be. Partselect is an awesome resource for knowledge and quality products with very reasonable prices.

I watched the installation video on "Parts Select". Unfortunately I watched it twice b/c the first part ordered last October only lasted 4 months. This part seems to be alright as the refrigerator has been running for approximately 6 days now - so far so good.

I watched the video a few times and pretty much did as it said to do. Took about 20 minutes start to finish. It seems to be working 100%.

I wasnt about to call Mr Appliance of Bayport NY the last time I called him I got a bill for $72.00 and he told me I needed a new frig. So I paid him then the next day I went to parts select and fixed it myself for about $50.00 But this time it was my Moms frig and the frig side (fresh food side) wasnt getting cold So again I went to parts select and put in a bimetel thermostat and it works perfect now. Im sure I saved a lot of $ and thanks to parts select, They helped me diagnose the problem and make the repair step by step! EASY! Thanks parts select...Garry from long island NY

all is fine now. thanks andy

Unplugged freezer, removed lower shelving, removed panel covering the evaporator motor. Unpluged three wires connected to fan assem and removed. Did not install new wiring that came with kit but installed new motor/fan and reconnected existing wiring. Problem gone!

Very simple repair. Followed the video instructions. Simply removed a few screws and nuthead screws. Removed the cover plates. Removed the old thermostat switch. Removed the plastics tubing over the temp sensor probe. Put the plastic tubing on the new sensor probe, ( rubbing a slight amount of vegetable oil on the probe to allow the tube to slide on easier,). Reinstalled the temp probe. Reinstalled the new switch. Connected the wires to the switch. Reinstalled the cover plates and screws. And the job was complete. Almost took me longer to write this out, than it did to complete the project. Hey, it was an easy fix.

First thing, I didn't have any idea how to fix my refrigerator, but I saw some videos on line, I just pull the start relay, it sound like little parts inside. I order to PART SELECT my Start Relay combination and part select have more comments, diagrams it was easy to find the part. Put the new start relay was easy, I just conect those wires back it took less than 10 minutes and it's working now.thanks to Part Select to make easy to fix it.

Grasped the base of the old part with pliers and turned a quarter turn until metal stays released and part could be pulled out (two online help videos: one says 1/4 turn clockwise, the other, 1/4 turn counter-clockwise, or, 1/4 in right direction, 3/4 in wrong direction). New part slipped in easily and snapped into place with 1/4 turn. Difficulty getting tray to seat fully until I whacked it with my open hand and it then snapped into place. Remains to be seen if it will be difficult now to remove.

Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!

First, although I was SURE I knew what to do, I watched the repair video. I used needle nose pliers to push broken support into wall since I could not pull it out. Selected correct wall fixture, spread holder pins, and snapped into wall opening. Couldn't have been easier!!! Very useful site.