59673504300 Kenmore Refrigerator - Instructions

Pulled the broken pantry door off, and snapped the new door in place. Vry simple.

take out two nut driver screws remove piece, take off track two philips head screws. transfer temp control rod, really easy then put track back on and install piece. probable took as long to remove the two veg crispers and glass top. this is a very easy fix. i did notice that the pin on the original was about 3/8 of an inch forward so flapper door did not quite line up and im sure caused the pin to snap off. the replacement part, the pin is exactly the same position as the other side. i believe the original was defective from the mfgr.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.

Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!

take the old one out replace with new once - no instructions required, no tools needed

Using socket wrench, took bottom right panel off on back side of refrigerator to expose compressor. It was very hot to touch, with no noise, signifying it wasn't working. It was a Tecumseh, TP142ar229b8. Evidently from internet search this is not a good brand. Turned off power at circuit box. Removed metal spring clip holding on white relay. Took off capacitor (black square piece) attached to relay. It was okay as I measured 15uF with multimeter. Disconnected electric cables to white relay by pulling off connector. Took off white relay with long cylindrical protrusion from compressor by pulling it straight off. Shook relay - pieces of ceramic fell out, indicating it was bad. Ordered and received new one (next day). Attached new relay to existing compressor by pushing it on. Replaced capacitor and electrical cables by pushing on. Replaced spring clip. Turned on power and compressor was working. Replaced bottom back panel.

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

You just take the old door bin out by sliding it up and replace with the new bin by sliding it down in the door.

I knew it was either the thermostat or defrost control board. Checked resistance with multimeter across the thermostat and heater element. Both check out ok so I replaced the board and all is good. Board on my model was in the controls panel.

Awesome! Couldn't ask for it any better. I watched the video from Partselect multiple time and was just as easy as they said it would be. It took me longer to watch the video four times than it did for me to install it. I have a habit of 10 minute projects turning into a couple hours and this took about 10 minutes. Thanks.

There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

I removed the 5/16 inch hex head nuts holding the rear access panel where the power cord was connected. Once removed, I released the Molex plug and ground wire. I connected the new cord, screwed in the ground and installed the rear panel. Having the exact OEM part made the job quick and easy.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!