10651753717 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- catherine from LEEDS, AL
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
ice would not chrush or come out into glass
removed 9 screws, removed all parts, laying them in order, so they would be easy to replace.
reassembled in order I had removed them placing the new auger drum in place of broken one.
replaced ice container in freezer, poured in a few ice cubes them crushed them.
reassembled in order I had removed them placing the new auger drum in place of broken one.
replaced ice container in freezer, poured in a few ice cubes them crushed them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from New Braunfels, TX
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The auger drum had broken & not distributing ice.
Once I removed the ice bin from the freezer section of refrigerator and removed all the necessary screws was able to remove the auger drum, but had some difficulty in reinstalling the crusher blades in the dispenser. After several tries, got it right and dispenser is performing like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WES from SPRINGVILLE, AL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch Controlling Light When Door Open Was Briken
Poped ou the old switch, connected new switch and pushed back into socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Racine, WI
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch broken
I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from woodland hills, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
you have to turn it off and on to run.
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joy from Laporte City, IA
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No crushed/cubes from icemaker
We took the icemaker apart, and took pictures of how it looked before so we knew how to put it back together, we were really surprised how easy it was to put back together, I will be ordering other parts from this company, I got my part in 1-2 days by Fedex, I will be telling others about this company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leroy from Clyde Park, MT
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice would not dispence because drum was broken.
Repair was easy enough, take apart and put it back in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CAMPOBELLO, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ice bin auger drum was broken
removed ice bin from freezer then removed front from ice bin then all i had to do was remove e clamp from end of shaft that made it possible for me to remove the ice crusher parts then slide off the drum. all that was left was to put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from long beach, CA
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
No ice coming out of the ice maker
Had to replace the auger drum. Went fairly smooth. The video that was linked next the part was a big help, especially when all the blades of the ice chopper came off of the shaft at once and I needed to get them back in the correct order. I did a freeze frame on the moment in the video to figure out the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Smyrna, GA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Frost in bottom freezer, freezer 8%, ice maker works
replaced electric control board, defrost for six hours. next day (24 hours) same problem, [email protected]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Palm Coast, FL
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Bin Auger Drum was broken.
Removed screws, Ice maker blads, and broken Auger Drum. Reverced order and replaced with new Auger Drum.
The manufacture needs to change the part from a plastic Auger Drum to a metal aluminum Auger Drum. This is the second one I had to change in 4 years.
The manufacture needs to change the part from a plastic Auger Drum to a metal aluminum Auger Drum. This is the second one I had to change in 4 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Fort Mill, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Ice Bin Auger Drum cracked.
It was a breeze to remove and replace. Made even easier by the previous DIY guys posts. Make sure you turn the nut at the end of the shaft clockwise to loosen. Taking a picture of the blades for ice crushing before removal for future reference is a great idea. It wasn't hard at all. Just take your time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Florence, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The auger drum broke from the shaft
I removed the 4 screws holding the front cover in place. Removed the 4 screws holding the ice auger cover in place. Removed the c clip holding the auger on the shaft. Pulled out the auger shaft. Removed the broken auger drum and replaced with the new one. Reassembled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lantana, FL
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Broken vanes in ice bin auger
Ordered part, watched video. Had a problem with reassembly of ice crushing assembly, did a re-do as one of the blades had dislodged from the drive shaft!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from Westfield, NJ
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Auger drum broken
Not so easy as others have described. I kept the parts off the auger together in my hand as I replaced the drum. Thanks to the people who mentioned the nut being left handed. Taking a picture before dis-asembly saved me. I would never have gotten it back together otherwise.
Was this instruction helpful to you?
Thank you for voting!