79570322311 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Franck from ST PETE BEACH, FL
- Parts Used:
- EAU60783850
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Icemaker not working
Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brandon from LIBERTY HILL, TX
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Old ice tray cracked and wouldn't hold water
Repair was pretty easy but be ready to possibly switch out the wiring harness. The new ice maker had a smaller connector that would not fit the connector built into the door of the fridge. I had to pull the harness from my old ice maker and swap it onto the new maker. After that was done, everything mated up perfectly and worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from ROGERS, MN
- Parts Used:
- 6600JB3001C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water/ice maker not working
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from TEQUESTA, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old gasket was damaged
i removed old and installed new gasket in 5 minutes. i watched a video. it was super easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jasmin from SUNRISE, FL
- Parts Used:
- AJP73874601, AEC73877501, AEC73877402, AEC73877401, ACQ86549505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Unable to use the parts to hold my crisper i actually need drawers not pieces to install there is no where to install those pieces you sent me
Did not the crisper cover is ok the vegetable tray is ok but the pieces you sent to me no actually fit the crisper in is way off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Homer from MARION, VA
- Parts Used:
- 4970JA3011K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Cold water control rusty and leaking water
Removed old part very easily and installed the new part without any problems. Used and adjustable wrench and screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from BOYNTON BEACH, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice buildup in corner of freezer.
Reviewed instructions on YouTube. Removed storage box.Removed Philips head screw on either side of track. Lifted door and placed it on table. Using a flat blade screwdriver removed old gasket (it did not looked damaged). Pressed new gasket into groove in door. Replaced door onto track and replaced screws. Replaced storage box. No more ice buildup.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- luis from DIAMOND BAR, CA
- Parts Used:
- AEQ73110210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice maker was broken
I just followed the instruction on the part , and everything was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorothy from SALISBURY, MD
- Parts Used:
- MJB63190001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace hand screw
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from SEBASTIAN, FL
- Parts Used:
- AJU72992601
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Slow water for drinking
Just like on YouTube very easy to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from TORRANCE, CA
- Parts Used:
- AJU72992601
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Valve assembly leaked
The assembly sent is different than what is on the unit. The connectors do not match. We called and it seems you don’t have the correct part. The only part we have found will only connect the ice maker or the water. It will be a shame if I have to buy a new refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Miami, FL
- Parts Used:
- 4004JA3002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
Frost in the freezer. Icemaker frozen.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Sun City West, AZ
- Parts Used:
- 4970JA3011K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Spring was broken on original unit, had to replace whole lever.
removed old lever ( 2 screws ) took apart electrical connection, replaced lever, connected electrical hookup, put in screws. DONE !!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREG from STILLWATER, NJ
- Parts Used:
- 4930JA3091A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
plastic tube leaking at connector
Uncoupled the old connector, replaced with new connector and attached supply line. Repair easy with right part, prior to ordering the right part I had tried a compression fitting and it still leaked. U-tube and others demonstrating repair assured me I was on the right path.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WHITE BIRD, ID
- Parts Used:
- 4681JB1027C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Blower motor out on condenser
followed detailed movie from Utube video
Was this instruction helpful to you?
Thank you for voting!