25360419614 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JEFF from OLIVET, MI
- Parts Used:
- 242044008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
FREEZER WAS COLD FRIDGE WARM
YOU TUBE VIDEO POINTED ME IN THE RIGHT DIRECTION. USED MULTI METER TO CHECK FOR VOLTAGE. NONE, REPLACED DEFROST HEATER. WORKS LIKE A CHARM, PART DELIVERED TO MY DOOR FOR LESS THAN $60.00, IN TWO DAYS FROM PARTSELECT. FIXED IT MYSELF FOR LESS THAN THE COST OF A SERVICE CALL.
Was this instruction helpful to you?
Thank you for voting!
Door shelf retainer bar snapped easily into place.
The fit was good even though the top retainer bar seems to be a tighter more secure fit than the middle retainer bar.The retainer bars are made to simply snap into place. Great to receive these replacement shelf retainer bars. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- winifred from LOUISVILLE, KY
- Parts Used:
- 297286803
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Coming from the refrigerator, there was an intermittent "clicking noise", occurring about every 30 seconds. The frig. eventually failed .
I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from GILBERT, SC
- Parts Used:
- 242193206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Torn gasket
Replacing the gasket is easy, just remove the old gasket by pulling it out of its grove and push in the new gasket in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Dallas, TX
- Parts Used:
- 240358008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
No shelf in Freezer compartment though obvious slots provided.
Used model # of frigidaire on your web site... reviewed parts available... noticed shelves abailable... zoomed in to measure using crosshatch background... measured my freezer compartment... seemed doable... ordered shelf... receivednext day... attempted to slip in slots... had to grind off 3/16th inch on two legs... slipped in... Perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ward from Stockton, CA
- Parts Used:
- 240534901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Refrigerator Door Shelf Retainer Bar
We took off the broken bar and put on the new one. It clips on. Took about 10 seconds and could have been done by a 5 year old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Raleigh, NC
- Parts Used:
- 240360908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator was missing a shelf when we moved in
Just popped it in and it fit perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deepankar from Novi, MI
- Parts Used:
- 240337103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper Pan
Just removed the broken pan and installed the new one within 2 minutes. Really simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from St Augustine, FL
- Parts Used:
- 240534801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken rack on freezer door
just slipped the part in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from 29 PALMS, CA
- Parts Used:
- 242193212
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The lining of the gaskets were falling apart and the freezer was defrosting
I ordered a freezer gasket/insulation lining; just pulled the old one out and put in pressed in the new one; solved the problem easily. Then the refrigerator gasket was falling apart. I was ready to buy a new refrigerator but then I got laid off from work. I ordered the 2nd gasket. It did not fit easily at all. My husband had to man-handle and stretch it; then it worked, as worked well ever since. Spent $250 instead of $1250+. Thanks. P.S. Could not find the year of the frig.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Shelbyville, IN
- Parts Used:
- 240534901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom retainer bar on door shelf broke
took replacement part out of box and slipped it right into placed. could not have been easier
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from GEORGETOWN, IN
- Parts Used:
- IM116000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Bought a new refrigerator. Did not come with an Icemaker.
Remove access cover at bottom of case w/socket wrench (4 screws).
Attach supply line to water valve with adjustable wrench. Attach water line to ice maker on back of case (twist lock) no tools required.
Attach water line from ice maker to water valve (push connection) no tools required. Attache water valve to case at bottom w/one screw. (nut driver)
Reassemble access cover to bottom of case w/socket wrench (4 screws). Remove plastic cover inside freezer (w/screw driver to release from evap cover) to expose ice maker harness connection. Remove two plastic plugs (carefully w screw driver) exposing screw anchors for mounting Ice maker. Assemble two mounting screws w/nut driver. (Do not dtrive all the way in) Plug ice maker harness to plug on back of evap cover.(no tools required) Place cover over harness connection) no tools required. Guide water fill tube into fill cup on ice maker. (no tools required) Hang ice maker on mounting screws. Level Ice maker and tighten screws. (torpedo level makes it easy if you have one handy. Place Ice bucket under Ice maker on freezer shelf (lower position). Turn ice maker on and you are ready to go. Easy Job!!!!
Attach supply line to water valve with adjustable wrench. Attach water line to ice maker on back of case (twist lock) no tools required.
Attach water line from ice maker to water valve (push connection) no tools required. Attache water valve to case at bottom w/one screw. (nut driver)
Reassemble access cover to bottom of case w/socket wrench (4 screws). Remove plastic cover inside freezer (w/screw driver to release from evap cover) to expose ice maker harness connection. Remove two plastic plugs (carefully w screw driver) exposing screw anchors for mounting Ice maker. Assemble two mounting screws w/nut driver. (Do not dtrive all the way in) Plug ice maker harness to plug on back of evap cover.(no tools required) Place cover over harness connection) no tools required. Guide water fill tube into fill cup on ice maker. (no tools required) Hang ice maker on mounting screws. Level Ice maker and tighten screws. (torpedo level makes it easy if you have one handy. Place Ice bucket under Ice maker on freezer shelf (lower position). Turn ice maker on and you are ready to go. Easy Job!!!!
Was this instruction helpful to you?
Thank you for voting!