2539308010 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from SMYRNA, DE
- Parts Used:
- 5303281398
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shattered glass shelf
Vacuumed out the glass and placed the new shelf in the slots. Arrived quickly and fit perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from ridgwood, NY
- Parts Used:
- 5303207230, 5303207229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken-door shelf retainer bar end caps
i simply snaped one end cap in put retainer in on sie put other end cap on retainer then snaped end cap in place --job done parts where perfect thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOYCE from CHICAGO, AL
- Parts Used:
- 5303207345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gasket was worn
Removed all the screws. Replaced the gasket put all the screws back. This would work great if the door wasn't out of alignment.
Now I have a new refridgerator coming on Monday.
Now I have a new refridgerator coming on Monday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from ANDERSON, SC
- Parts Used:
- 216594300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer was not freezing.
I removed the compressor start relay and replaced it with the new part. Initially it did not work. When I checked my work, I had to tighten the connector on the new part. Once I made the correction, the freezer is freezing normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- toney from poplar bluff, MO
- Parts Used:
- 5303207345
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
gasket needed replaced
took off the old one installed the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gaynita from Philadelphia, PA
- Parts Used:
- 5303207345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door gasket was ripped and food wouldn't stay cold
First I removed the old gasket by pulling it off the door. Then I removed the screws from the door. Next I placed the new gasket around the door frame. Finally, I replaced the screws in the door to completely attach the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- earl a from GIRDLER, KY
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light blub blew
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from Ayden, NC
- Parts Used:
- 216594300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer just quit working. I could turn thermostat off. Click ever few seconds would stop..I figured the thermostat was good compressor not starting
First unplug it and pull away from wall to gain access to the Rear of freezer.
From the rear of the freezer. You can clearly see the compressor.....I had to lay in the floor. Best way to see what your doing .
Attached to the side of the compressor
Is square cover over the start relay..it has a metal bail that retains the cover. Simply remove the strap with a flat blade screwdriver the cover can then be removed. A flashlight and screwdriver is all I needed
The switch body plugs onto the compressor with pins or blades. Mine broke in a few pieces by the time it was completely removed. The start switch has very tight connections so its a bit of a struggle to get it off. ..stick screw driver behind it and try pry evenly until its off..secure new switch on the pins and push it in ..there is one single wire attached to the start switch no confusion there.install cover and its retainer and its done..
From the rear of the freezer. You can clearly see the compressor.....I had to lay in the floor. Best way to see what your doing .
Attached to the side of the compressor
Is square cover over the start relay..it has a metal bail that retains the cover. Simply remove the strap with a flat blade screwdriver the cover can then be removed. A flashlight and screwdriver is all I needed
The switch body plugs onto the compressor with pins or blades. Mine broke in a few pieces by the time it was completely removed. The start switch has very tight connections so its a bit of a struggle to get it off. ..stick screw driver behind it and try pry evenly until its off..secure new switch on the pins and push it in ..there is one single wire attached to the start switch no confusion there.install cover and its retainer and its done..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from WOODBURY, TN
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator light would not work ...even after replacing the bulb.
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roland from Stoneham, MA
- Parts Used:
- 5303001015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Handle and End were missing
After first ordering the wrong end part, I reordered the correct part and successfully attached the handle end and handle to the refrigerator door. The handle itself was too long, and I had to cut it down to the correct size. I am a realtor and provided the service to my buyer of the condo that was my listing. Thank goodness for your company and the ability to buy parts for an old model!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HELENA, AL
- Parts Used:
- 218906802
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Getting the light socket to snap back in properly
It snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie from West Plam Beach, FL
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Shelf
1) Remove glass from shipping Container. 2) Using fingers, place glass ever so gingerly in the shelf tray. 3) Pour a glass of wine to celebrate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Albuquerque, NM
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems at all.
Very EASY!! just unpack, wash, and place into slots above crisper doors. A child could do this.
Was this instruction helpful to you?
Thank you for voting!