2539658300 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from Orange Park, FL
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clips on both end caps we broken and the crossbar kept falling off.
First i pulled the crossbar off the door, then I pulled both end caps off the crossbar and then I
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brad from minneapolis, MN
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer okay, but fridge was warm
Website was great!
The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.
To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.
The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.
To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from San Marcos, CA
- Parts Used:
- 5303207345, 218998902
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Old gasket not fitting correctly
Removed old gasket and installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Stuart, FL
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
coil Iceing up
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Oconomowoc, WI
- Parts Used:
- 215366002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf bar with missing end brackets.
Ordered the parts from the product discription (photo) as well as chart showing actual size. Got the parts( in two separate shipments) cut the bar to length and snapped them inot place. Bingo!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HELENA, AL
- Parts Used:
- 218906802
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Getting the light socket to snap back in properly
It snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Fort Sill, OK
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We Are Moving Out Of Military Housing And We Had To Replace The Freezer Door Holder Before We Moved Or We Would Have Had To Pay For The Wholr Refrigerator
We replace the end pieces to hook the holder back on the door.
Was this instruction helpful to you?
Thank you for voting!
could not use the meat drawer as it kept falling off
I removed the screws that were in the original part that had a broken plastic endpiece on it. Put the new hanging rail on with the screwdriver and good as new!. I also replace some clips that were worn out and kept coming off when I put too much in the freezer doors. They were snap on so it took less than a minute to replace all 4 that I ordered. Now my refriderator and freezer work like it new and doesn't keep falling apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Defiance, OH
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
leaking water down into fridge
just like the video showed...it was excellent!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Glendale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
ice buil up on freezer,not defrosting
first I replaced the timer control hoping thats the problem,unfortunately situation the same ice build up on the freezer.so I replaced the defrost thermostat.right now I'll still observing the condition if still the same.may be in couple days.so far its good.and to replace the parts is not difficult and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from San Angelo, TX
- Parts Used:
- 5308000010, 5300158289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Fan Motor was making noise and freezing up.Fan was missing one blade.
Removed screws that fastened bracket to fridge. Next, I replaced the motor and carefully lined the brackets up so the motor would rotate smoothly. Put the fan blade on the motor and screwed the brackets back on the fridge. Motor kept popping out of alignment while I was screwing the brackets back in but I kept snapping it back in till it stayed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from marietta, GA
- Parts Used:
- 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
fridge not blowing cold
bottom left cornerof fridge defrost timer replaced two bolts and a wire
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Dunnellon, FL
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
both ref&frez were hot
1 went with maj 69% said defrost timer. NO. 2 went with second choice run cap NO. 3 went with my thought, ( PTC Starter ) why not, most exp part. Fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Bloomington, IN
- Parts Used:
- 5300158289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan Motor Noisy
Emptied freezer, removed fan motor cover (2 screws), removed fan and motor (2 screws), removed old motor from bracket and reassembled with new motor, transferred fan blade from old motor to new), re-installed new fan/motor (2 screws) and reinstalled cover...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Waynesburg, PA
- Parts Used:
- 5300158289
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fan Motor Malfunction
Followed the instruction video. Removed the old one. Attached the fan blade, ground wire and connected power plug. Reinstalled with 2 screws. Works great.
Was this instruction helpful to you?
Thank you for voting!