10651119710 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from ALBANY, GA
- Parts Used:
- W11578915
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
fan motor needed replacing
System not cooling. removed back cover and notice fan not rotating. Looked up unit and found diagram. Ordered motor which was received in less than 5 business days.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric S from Boca Raton, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
OLDER Ice Maker on the fritz
Grat help on the phone. We saw repair on YouTube. my wife and I worked it together. It was child's play!! It went beautifully. we were able to "chill out" with ice aplenty!!Thanks...eric
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from SWANVILLE, ME
- Parts Used:
- W11338583
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer Bulb failed
Unscrewed bulb from sock .
Replaced with new one . Now working
Replaced with new one . Now working
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BONITA SPGS, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
install ice maker 2 screws wire harness pluged in done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from EDEN, NC
- Parts Used:
- WPW10300022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
No ice making.
Took old ice maker out; put in new ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randolph from Derby, KS
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Auger blades separated from hub.
First I removed the screw holding the ice door shaft (at the rear of the ice container). Removed clip of which the screw was holding in place (no need to remove the clip from the shaft). Then I removed the front cover screws, separated front cover from ice container. Door shaft is removed with front cover assembly, no need to remove anything else from front cover. Pulled out auger shaft, removed circlip (snap ring) and washer from front of shaft. Used an adjustable wrench to remove plastic nut from front end of shaft. CAUTION - the plastic nut is reverse thread, make sure to turn it clockwise to loosen and remove. Pulled off broken auger then reassembled with new auger in the reverse order as previously described.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia denise from tullahoma, TN
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
the ice bin auger had broken
i used the instructions that came with the part and it was really simple. thank you very much. it saved me a HUGH repair bill.we use alot of crushed ice and the part shipped in 2 days. thank you.C.D.L.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Dacula, GA
- Parts Used:
- WPW10300022
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped working
Ordered the part from parts selection and when it arrived I unpluged my refrigerator and removed the ice bucket to get to the ice maker. I than looked at what needed to do to remove the icemaker. I removed the icemaker and swapped the parts from the old one and reinstalled the new one. If you don't have any mechanical abilities then have someone that does to help you out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SWAINSBORO, GA
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Auger Drum broke
I followed the instructions on your video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EUEL from NICHOLS, SC
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Drum was broken
Replaced drum and reassembled unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOEL from LUMBERTON, MS
- Parts Used:
- W11671282
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
ice will not dispense ice from storage bin to out the door. Auger does not turn
Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from Chunchula, AL
- Parts Used:
- WPW10197428
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Removed old part and installed new part
Took off panel in back and located part, removed it and installed new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Butte, MT
- Parts Used:
- WP2315549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Fan making noise
Removed existing fan. Access wasn't too dificult. Motor access was easy to access and remove. Disconnected old fan and the replacement part fit perfectly. Runs perfectly.
Was this instruction helpful to you?
Thank you for voting!