25363702202 Kenmore Refrigerator - Instructions

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.

took out old screws and put on new handle. with the same screws

I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

You guys at Partselect are the best!!! Went to your site, typed in my appliance symptoms, and received possible fixes. Ordered the suggested parts (under $50) on a Sunday night and got em Tuesday am. Installed the easiest one first and Voila!!!! Frig is working great. Thanks Bob S

Remove 4 screws that hold up overhead controls, this is also the part that holds the light. Unplug the timer and replace. Super simple and runs great now. After you plug it in it may take a few minutes to kick on the compressor but it will. Also I was pleased it was a factory Frigidare part. Price was right.

Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

I watched the video you had on-line and it was simple. Thank you so much

Followed instruction vedeo from partselect. THANKS!!!!!

When my side by side Kenmore refrigerator quit keeping the top half of my freezer and refrigerator cold I called Sears to see how much it would cost to get it checked out and fixed. Bottom line it was going to cost minimum $65 (which was just for him to come out) to $250 on up depending on what the problem was. So i decided to "do it myself"! I took it apart and within a few minutes figured out that it was my evaporator fan. So I went to sears to order the part based on the part number and with shipping and handling it was going to cost $125. While at sears I got on one of their computers and quickly looked up Kenmore parts and partselect.com came up and I quickly found the part for $62 and I chose overnight delivery and spent a total of like $83. When my part arrived I realized that the wiring/plug ins didn't quite match up. So I got online and went to their website and found a video for "do it yourself'ers" like me on how to splice the wiring to make it match. It took me about 20 min to splice the wire and put my refrigerator back together and IT WORKED! Easy easy easy and I saved moocho bucks! Ill never pay a repairman again. Oh and by the way, I am blond! :-)

I watched the step-by-step installation video and followed the instructions therein.

My husband watched the video on your website and found it very easy to do the repair. The repair company that diagnosed the problem wanted $210 to do it. The part I ordered was under $20, and after he installed it the refrigerator has been working great. We would highly recommend your site to anyone who needs to fix anything!

bottom left cornerof fridge defrost timer replaced two bolts and a wire

Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!