1069638282 Kenmore Refrigerator - Instructions

Pulled up part select video on u-tube. Followed instructions on dissambly of top freezer and found condensor freezing up blocking air from refrigerator. Checked timer to make sure it was good. Next checked continuity on heater to make sure it was good. Last checked bi-metal thermostat for continuity while cold. Found Bi-metal part to be defective (also rubber in top of was popped up which is a sign of a bad part). Simply ordered new part from Part Select, received in 2 days and replaced Bi-metal and melted ice with hair dryer and reassembled freezer. While waiting on part you can still use refrigerator by melting ice so air can get to refrigerator. I put a towel in bottom of freezer to catch water. Greg W. in Ga.

Went to various websites looking for guidance. Finally went to PartSelect since I had previously purchased dryer parts. I entered the model info, etc. from my refrigerator and ordered the ice maker installation kit. The install was fairly easy and everything worked perfectly. I am very satisfied I could do the work myself versus calling a repair technician.

Emptied the freezer. Removed the back panel. (six screws)Removed the fan cover.(4 screws) Unplugged the power. Unplugged three wires from the motor. (hot-neutral-ground)Removed the fan. (2 screws) Installed the new fan and centered for clearance. Reversed the prior instructions.

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

Ordered the complete ice maker kit because I wasn't sure which part went bad. I replaced the ice maker assembly first which was very easy to do. I couldn't tell if the new ice maker was doing anything. I waited almost 16 hours before the ice maker started to run and make ice. I would just say to be patient after installing these parts if you don't immediatly see anything happening. Saving the solenoid and other extra parts if needed in the future.

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck

took shelf off of freezer, took ice cube maker out, took back panel off changed defrost thermostat.then re-assembled.

Just followed the video that you guys had on line . It was a very easy repair

My husband and I are novices when it comes to repairing ANYTHING. This was are first attempt at repairing a major appliance. I love my refrigerator which came with the house we recently purchased. We followed the instructions provided by the Parts Select videos and the instructions that came with the parts we ordered. It was really easy, a few things were different in the video because our fridge is over 10 years old but not too hard to figure out. Follow the video and paper instructions and you can't go wrong. We took out the food and put in our second fridge and freezer, unplugged the appliance and let it defrost for 24 hours. We vacuumed the coils which were really clogged with dust and used a wet dry vac to drain the water collection pan at the bottom of the fridge. We took of the back panel of the appliance and located the Run Capacitor as instructed in the video, unplugged the bad one a replaced with the new one. Easy to do, took 15 mins and that was because of where the part was located. To replace the Evaporator Fan Motor with Fan Blade we took the back panel off in the freezer, our fridge has the freezer in the top, unscrewed the old motor and replaced with the new one as instructed by the video. Double checked everything with the paper instructions and replaced the back panel 15 to 20 mins. Our refrigerator is running like new.

I followed vidio instructions, took about 15 minutes. Fridge making great ice cubes again. Felt prouud of the repair I did being 70 years old and a female. Thank you

It started out being a disappointment. I just moved into a new place that needs many repairs so I didnt want to spend too much time on this one. I ordered this part which arrived in just a few days. Not knowing exactly what was broken I just ordered the whole thing. When I opened the box, the first thing I noticed was that one of the parts of the new ice maker had a big crack in it. Not wanting to go through the hassle of boxing it up and going through the return process, I started taking it apart and replacing the worn or broken owned, (exactly why I ordered the entire unit). Nevertheless, I wanted ice so I fixed it with some of the new ones and some of the old ones. By now I've paid too much for the unit but it was my choice not to send it back and I now have ice. It was pretty easy to fix once I had the parts.

Unplug the refrigerator. Remove the rear shelf supports by lifting them straight up. No tools required. Remove the screws holding the rear cover of the freezer. Use a nut driver to remove the 4 screws holding the fan housing. Unplug the wiring harness, then remove the fan and install the new one. Remount the housing, plug in the harness replace the rear cover, install the shelf supports and plug in the refrigerator. It was 30 minutes start to finish, which includes the time to gather the tools, unload and reload the freezer, and putting the tolls away!

First I entered my model #, then picked the symptom, then went with the odds when presented with the likely suspects. The run capacitor, and bi-metal defrost timer had the highest % of guilt. Most of the time was spent defrosting the coils with a hair dryer. The run capacitor took 3 minutes to remove and replace. I snipped out the old defrost timer and used butt connectors to wire up the new one. The old timer flunked the continuity test when placed in salted ice water. The freezer/fridge runs like new, for about $66. The run capacitor was probably ok but I left the new one in, being too lazy to send it back. "Part Select" was a great partner in helping to fix my machine.

repair went well. Ice maker still not making ice. UGH

The repair was super easy and the part worked like a charm. I love my new ice maker! I had to take out the top freezer shelf just so I could fit my head in the freezer to find one screw, but otherwise all went fine. Ice maker is held on with two top screws and one bottom screw. Loosen the two top screws, remove the bottom screw and lift out the ice maker. It plugs into wires on the inside, back of the freezer so this has to be unplugged. Plug in the wires for the new one, slide it down onto the two top, loose screws, tighten those and screw in the bottom one, replace freezer shelves and you are ready for ice...with no huge iceberg fouling up the ice in your ice cube tray. Simple! The wiring thing worried me when others described it, but it's no harder than plugging in a lamp, really. If I can do it, anybody who can stand on a shorty ladder can do it.