25331444300 Kenmore Refrigerator - Instructions

After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.

so basically if you can make toast , you can do this repair....loosen 2 hex head screws ,lift up on the ice maker and separate from wall of freezer , unplug the wire harness ,it is now OUT , swap the water level indicator to new part [30 second job ] Install the new part in reverse order as mentioned above... enjoy your ice

The repair was not difficult because you just remove the old part and plug it in and connect two wires. But I wish there was a way to test if the compressor is working before I purchased the parts. The compressor would not start so I was not able to repair the refrigerator.

Remove ice pan below ice maker. Got mirrow verifed the type of screws. Obtained nut driver and felt it at right angle remove screws only have way. The ice maker lifts up and off. Took needle nose pliers to grip and remove electrical connection plug. The instruction and picture sent was no help the picture were the size of a thumb nail no detail could be determine. I installed the adapter plug and all the extra length wiring was the most difficult to type wrap with both hands extended out in front. I finally wrestled it in on to the two screws unscrewed from the wall about 1/2". Keep the ice maker water lever up and ensure it aligns to the water trough inlet. Works Great.
glg

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.

Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.

Had to reach right hand to top of ice maker to locate hex head screws by feel, then place nut driver onto hex head by feel and then unloosen screws with lft hand ,a couple of turns, enough to lift ice maker off screws.
Replace new icemaker onto screws and tighten screws. The only problem incountered was the location and availability of having to feel with both hands to fit nut driver onto the screws.(could not see with my eyes because front of ice maker blocked view. )

I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

Real simple repair..just backed off the two 1/4" hex bolts holding the ice maker to the wall of the fridge,(a little tricky since you can't see them),unclipped the electrical doo hickey. I re-clipped the electrical do hickey of the new ice maker, hung the ice maker on the bolts and then re-tightened them. However,still no ice,my problem was the water valve on the back of the fridge behind the cardboard. Although it was still giving H2O thru the door it was not allowing water to flow to the ice maker. I reccommend pouring some water into the ice tray of the ice maker. If it makes ice and dumps it in to the holder, your ice maker is OK. If it turns out to be your water valve, that fix is easy as well. I HIGHLY reccommend watching the "fix it" video associated with that part. That repair also took less than 15 minutes. Good Luck! KC Bridgewater,NJ

Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Received fan blade part took about 5 min to install and running great.

It just snaps in place, no biggie. What was a big deal was... that I ordered the part one day at like 2pm and got it the next day by about 2pm. That was very strange!!! Never expected that sort of delivery. Very nice!

Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.