5968590810 Kenmore Refrigerator - Instructions

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

replaced the entire ice make - 3 screws and a squeeze -off connector and it's out. Reverse to re-install... except that the fill tube had iced up. To thaw the fill tube: unload freezer section (leave food in fridge, but keep door closed), remove ice maker. Boil water, dip drill bit (dull end) into hot water, swirl around, insert (dull end) into to fill tube. Depending on how hot you got it, maybe a tablespoon of ice will melt. Repeat many times - fill tube is about 14" long! Do not use anything sharp - you will nick the tube and ice will form causing you to repeat this procedure. Do not try to break the ice - let the heat work. It took me about 30 minutes to thaw the whole thing - it made a nive gasping noise when the final plug opened up. Re-install ice maker.

First turned off the water and unplugged the refrigerator and then removed the old ice maker by first removing the side cover plate and then next removed the ice level detector. Remove the screws that hold the ice maker in place and rotating it somewhat soas to gain access to the wires and then unplugged them. Next I had to modify the way the water comes into the new icemaker by adapting a CPVC street ell to fit into the hole on the side and then hook up the water supply. Installation is just the reverse of removal.

Part received was what I needed. There was one issue--the 'feed' opening to receive water and direct it into the ice tray was a side feed and what I needed was a back feed. That means I had to do some exchanging of parts to make it work. That exercise took more time that the actual installation.

Emptied the door.
Removed the door, top bolts first.
Lifted out the door.
Installed new cam at the bottom.
Set the door back in place.
Bolted the top hinge back on.
Smooth!

The part came quickly and was the right one. You can't imagine how many outfits lose it here. Well done and thanks.

Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new fan. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.

Removed the door by taking 3 screws out of the top and lifting straight up, then replaced with the new parts and very easily replaced the door, worked ike a charm, if i didn't know any better it was like factory new

I read the previous repair story and agree with the author that the screw behind the front piece was difficult to remove and re-install. If I had a magnetized nut driver I think it would have been easier. There were no installation instructions so I relied upon the repair experiences. The other two screws came out easily and I found the harness release easily and the harness was easy to reinstall.
I am not a good handyman but was able to install the new ice maker

installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

Replacing the icemaker is pretty simple. Three screws, an electrical connector. Hardest part is getting to the icemaker since the freezer is below the refrigerator.

Removed top hinge cover and socketed out hinge nuts. Lifted door off bottom hinge. Socketed out broken bottom cam and replaced with new. Reset door with someone lifting and the other guiding. Reattached top hinge and cover. Voila.

Ice maker assembly required disconnection of the wire harness at the back of the freezer and the removal of 3 hex nuts. The assembly did not come with a new wire harness nor the rigid wire attached to the hinge that can be raised to stop production of ice. The wire harness was easy to disconnect from the old assembly by pressing in on a tab. The rigid wire attached to the hinge simply required pulling straight out of the hinge-hole (no need to twist, slide, or perform other contortions...it does require significant force to remove, but it does pull straight out). It was simple to attach it to the new ice assembly. Reinstalled the 3 hex nuts and wire harness plug and was good to go....after waiting several hours! I was worried at first because the unit did not immediately fill with water after I plugged the fridge back into the wall socket. However, after the freezer was cold enough, the water did run and I had my first ice dump within about 3 hours of finishing the installation. We have good ice again, and Partselect has excellent pricing and awesome delivery! I received the unit the day after ordering, and I had only paid the basic shipping! Thanks Partselect! Jeff

Unplug wire harness back of fridge. Unscrewed 4 screws on guide for ice bin. then unscrewed two screws holding ice maker to wall of fridge. removed ice maker. then had to take front cover off (pull hard, it comes off) and remove wire harness plug from the ice maker. save this, front cover, and all hardware to re-use. reverse steps to reinstall, including wire guide that goes up and down to stop and start ice maker when bin fills. Have to put this into front part of ice maker correctly for it to work. make sure it is down so that it will produce ice. ice tray took a few hours to fill with water initially, must be on a timer or something.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.