3639454280 Kenmore Refrigerator - Instructions

I was astonished when my part (PS306943 SLIDE ASM LH (Drawer Slide Rail - left side)arrived the very next day!!
In a big box, beautifully wrapped.
I got out my screw driver, detached the dead shelf support and screwed in the new one.
Oh it's so very nice to have the fridge working again, and so soon.
Hooray for Part select.com
The best thing since sliced bread.
Jill

Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.

put block of wood under the door, removed old hinge and installed the new one. about 15 minutes

Removed 2 screws on each slide, Screwed in new slide. Done! The hard part was picking the correct part #. Ordered the wrong parts. Parts Select representative helped me get the correct part # and assisted with the return. Thanks.

Installation could not have been easier!

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.

quick and very easy to enstall

First I removed the two screws that held the old slide to the refer side wall, (after unloading the shelf and taking out the Veg. draw). I then put the screws in the new slide spots and screwed them into the refer wall using a hand screwdriver (phillips) and put everything back in place. It was about as simple a repair of anything I have had in the past 75 years. I didn't even have to swear.

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

The isnatalla tion was very simple, two screws, and that was it. The only problem was ttying to determine if it was the right side or the left side rail

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

It seems my refrigerator was old enough [1987] that the spacing on the holes for the bracket were different than the part that is currently sold. The holes on the new bracket were 30 mm apart on center, but on the old bracket they were 20 mm apart on center.

Clamped the old and new brackets together in a vise to use the old bracket for spacing and drilled a new hole through the 4mm of steel.

After which it was a snap installing the new hinge assembly.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think about offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.