3639517926 Kenmore Refrigerator - Instructions

It was exactly as shown in your instruction video

I spent 15 - 20 minutes just hunting/deciding which of several sets of parts & directions to follow. The provided directions were not bad; but none of them quite matched my GE ADORA side-by-side model. Once I came up with the actions I would need to take...I was done in 5 minutes! The kit , as I said, came with all the parts one could need (and one or two un-needed parts included for other model GE refrigerators) I am very happy with PART SELECT...altough GE doesn't rate as high with me for their declining reliability.

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

Followed the instructions. Smooth as silk. This part is better than the original. There appears to be a sensor that beeps when the ice reservoir is full.

1. pry off small square plastic cap on top and bottom of old handle with thin blade tip of paring knife. Careful not to damage small tabs on the backside corners. 2.Pry off long trim insert above the handle with the paring knife and loosen bottom most screw revealed. 3. unscrewed 2 screws revealed by step 1, one on upper handle end and one on the lower. 4. pull upper cap end from the door and lift the handle upward and away from the door. 5. slide the new handle and door end into the lower trim piece. 6. fasten all 3 screws. 7.snap in upper trim strip and square plastic caps back in place.

Removed old ice maker, then screwed in new ice maker. Only thing that was a little difficult was to hold the auger motor, while trying to unplug the clipped in plug on the old ice maker. I could have used an extra pair of hands.

Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

Went to GE website and researched the problem for the model, determined that it was 90% sure it was the Ice maker, I ordered it and it arrived the next day, installed it and it began working immediately,

Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

Replaced auger and front helix kit.

I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

I ordered a new micro switch that was activated by the high ice lever. Once the switch was replaced the ice maker cut off as it should have and stopped producing too much ice. YHis job was of moderate skill level, the most challenging was replacing a spring that popped out then reassembling the unit.

I simply ordered a new Ice bucket, removed about 6 Phillips head screws, removed the old bucket from the Ice door and replaced with a new bucket. SIMPLE !!!!!