25360742400 Kenmore Refrigerator - Instructions

I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator

Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.

I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

replaced it

All 3 parts were very easy to replace. Thawing out the freezer took the most time. Great videos that go with each part for installation. I will be purchasing again from this company when needed.

Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.

Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

just like the video showed...it was excellent!!!

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.

I hesitate to say anything since I did exactly what their video told me to do, and it fixed the problem. Couldn't be happier. Was positive I was looking at 1000$ for a new fridge. Love being able to fix it by installing 15$ part myself. Thanks guys.

First of all I am 78YO, retired. Handy but NOT a handyman. There were two parts to replace. The Defrost Timer was very very easy and went just like the video. 20 minutes at the most. No surprises with only the most basic tools. The Defrost Thermostat was a little trickier. Took about 1 1/2 hours. The Thermostat disconnect plug was not like the video and was stuck hard. Had to use two needle nose pliers to finally get it apart. The rest went OK. The shrink seals were way too large for the job and my Hair Dryer was not able to shrink them enough for a good seal. Used a much smaller shrink seal that a friend had and it worked great. Suggest they use a smaller shrink that works with a hair dryer instead off the blow gun in the video. Wrapped the connection with electrical tape as others have suggested in addition to the Shrink Seal. Went together easy and am very very happy camper. Saved $295 from the Sears Repair Estimate. Dave

I watched the video you had on-line and it was simple. Thank you so much