1067660660 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Howell, MI
- Parts Used:
- 833697
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from State College, PA
- Parts Used:
- 833697
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Refrigerator would not stay cold
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Replaced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Was this instruction helpful to you?
Thank you for voting!
Did not work light does not come on when the door opens. Would try the light socket. It not sure how good the switch got plugged in.
By watching a video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Jefferson Hills, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Internal light did not come on each time the door was opened.
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from North Scituate, RI
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken light switch
Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from PARKER, AZ
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Filler Tube Broken At Elbow Where Line Hooks Up To
Replaced fill tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felix A from Orlando, FL
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Part broke.
Replacement partfit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Watertown, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
19 year old light switch broke
Great service. Unpluged old switch and pluged in new one. Works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Jenkintown, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights didn't always come on when was opened
Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- uri from riverhead, NY
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
thread broke
Unscrew broken piece, pull it out and then insert new one, security it in place and connect water line again, make sure It's thight check for leaks and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Hinsdale, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Light switch cracked Mounting
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Sellersburg, IN
- Parts Used:
- WP2196157
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
The fill tube froze and cracked
It was easy and quick to find the part that I needed, order it and have it shipped. The fill tube arived in 3 days and was easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JONATHAN from ELKINS PARK, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
old switch left freezer bulb always-on
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from middle island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light would work intermitently
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Pelham, NY
- Parts Used:
- 4386774
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the front wheel broke
First I had to tilt the refrigerator on wood on the supports under the refrigerator, the wheels were easy to get to then I unscrewed the old ones and replaced them with the new better wheels. The old ones where plastic.
Was this instruction helpful to you?
Thank you for voting!