2539305181 Kenmore Refrigerator - Instructions

The repair was a simple swap of icemakers with a 1/4" nutdriver. I didnt get the first unit sent after 7 days, so I called PartSelect. They were very courteous and understanding. My icemaker arrived within 12 hours of my phone call! Excellent!

was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.

Turn off water, un-plug refrigerator, dis-connect water, un-screw bracket, remove valve and replace same way...Very easy

I needed one with the adapter. I installed it and there was ice in the tray the next morning...no problem

put in a new one

Fast and easy. Started by pulling out refrigerator and unplugging it. Water valve for ice maker was already turned off due to leaking. Disconnected old valve, detached old valve, reattached new valve and reconnected water lines. Bled the lines and turned back on. Make sure temp in freezer stays at recommended temps for ice making.

This would have been an easy repair, but I bought the Frig from Lowes and I think they added the icemaker. The replacement icemaker uint has a plug on it for easy replacement. My frig was hard wired so I had to cut off the plug and splice the wires. Not a real big deal but a small work space.

1-Unpluged the refrigerator 2- removed ice cube tray and some food( Placed in cooler )3- unscrewed the two screws holding the old unit lowering it and unplugged it. 4- Had to loosen the cooling coil to get to the pass through hole in the back and pulled the old wire out. Connected the wire adaptor to the old connectorand to the new ice maker. At this point I couldn`t pass the new plug through the back so I strapped it out of the way and installed the new ice maker using the two screws from the old one. Adjusted the fill adjustment and turned it on. Cubes in about 4 hours.

I watched the video and did the same thing on mine and now it is working fine

According to the online video instructions.

Took less than 10 min to install following the inclosed instructions. At first it was not making enough ice to make me happy so I set the temp. a little colder in freezer. Now making ice like crazy. Works better than the old one ever did. Very happy with the new replacement.

I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

instructions were very simple. Took about 10 minutes to replace the unit. Do NOT get excited about immediate ice because it took mine awhile to g et cranked up for full production. Anyone can do this! Saves about $150.00 in labor to have someone(no smarter than you) do it for you.

Unplug refrigerator power cord. Remove ice cube bin. Place wire signal arm in down (off) position. Ice Maker is held in place by two (slotted/hex headed) screws through keyhole slots over the top of Ice maker along the left side of freezer. Use mirror to locate screws then carefully loosen (do not remove) screws with a nut driver or screw driver. Lift Ice maker up and right until it releases from the screw heads. Unplug electrical connection. A flat screw driver may be required to loosen connector. Connect new unit electrical and Install new unit over screw heads and tighten screws. Replace Ice Bin and place wire signal arm in the up (on) position. Reconnect refrigerator power cord. After freezer cools down sufficiently it will start making ice.

moved freezer items to right of icemaker,loosen two nuts lifted icemaker over nuts,squeezed and pulled cable out turned over marked L bracket screw with marker for location plugged cable in tighten screws,made ice in 2 1/2 hours john