79571052013 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Philip from Ashland, MA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lights didn't come on when door was opened
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from IMPERIAL, CA
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken spring on flapper door
Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TONAWANDA, NY
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad switch
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Northome, MN
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from MURRIETA, CA
- Parts Used:
- MAN38143001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken plastic/glass
Now that you have to buy a complete assembly that includes the drawer in the classy window it's very simple to replace however you buying parts that you don't need simply because G no longer makes the window. Which I find rather odd being as though that they make the whole assembly think and sell windows by themselves for less than 2/3 of what I spent through the whole assembly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CURWENSVILLE, PA
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JANET from GRAND JCT, CO
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spring on the mullion was broken so the mullion would not open to seal the other door.
I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PENNSVILLE, NJ
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from NORTH AURORA, IL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Removed old part.
Installed new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from MERRITT IS, FL
- Parts Used:
- AGU75188619
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old part did not seal properly
Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karyn from DURHAM, NH
- Parts Used:
- 6600JB1010A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from BOYNTON BEACH, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice buildup in corner of freezer.
Reviewed instructions on YouTube. Removed storage box.Removed Philips head screw on either side of track. Lifted door and placed it on table. Using a flat blade screwdriver removed old gasket (it did not looked damaged). Pressed new gasket into groove in door. Replaced door onto track and replaced screws. Replaced storage box. No more ice buildup.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from YORKTOWN, VA
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Lower ice maker water feed froze and caused leak. Needed new water valve.
Took pics of original install, removed old valve, water tubes & plugs. Installed new valve, reconnected electronic plugs, water tubes, turned water back on and all has been well since. Thank you for your timely delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from TEQUESTA, FL
- Parts Used:
- MDS38201426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old gasket was damaged
i removed old and installed new gasket in 5 minutes. i watched a video. it was super easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from BETHPAGE, NY
- Parts Used:
- AJU72992601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice Maker and Water dispenser stopped working
Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.
Super SImple/
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.
Super SImple/
Was this instruction helpful to you?
Thank you for voting!