1065907890 Kenmore Refrigerator - Instructions

i didn't repair replace capacitor, bi metal defrost thermostat and still not freeze also replace light door switch any suggestion thanks

Just follow youtube examples. Work in freezer. Troubles was I didn't fix the problem. Experts say thermostat is the best one to replace (53%). Anyway they are not always right.

with vidio

When you plug in the fridge it will begin to make noise, but never get cool. When you open the door it will stop and will not turn back on.

This part is listed as one that can fix the problem, but the installation video does not match my fridge.

I've replaced the capacitor (PS11757023), the compressor start relay (PS11740412), and condenser fan (PS1957416) and none of them have fixed the problem.

I really don't want to throw this fridge out. Please help! justin@jplt.com

We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel was easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.

All food and drawers were removed from the freezer, including ice tray. The left side shelf brackets were removed to ease removal of the back panels which expose the the bi-metal defrost thermostat. Six screws to remove the large back panel, plus the shelf support rails needed to be loosened to remove the smaller upper panel. The bi-metal thermostat is mechanically clipped to the upmost coil of the condenser. The two wires must be cut and wires for the new thermostat spliced in. The wires were tinned with solder to insure a good connection, then twisted and crimped with an automotive end connector. With the smaller 22. 8 Cu. Ft. Refrigerator a lot of the work will have to be performed with one hand. The hardest problem here is diagnosing the malfunction correctly in the beginning. I was impressed that the replacement part was received in two days . . .

I spent several hours defrosting the unit. Making sure the vents were all defrosted and free of ice. The part replacement is fairly straight forward; remove the thermostat, cut two wires, reconnect the wires following color codes, attach to coil and restart. And, "Yippie!". Nothing. Zilch. Zero. Because I could not connect with the online repairman, I spent 40 bucks for nothing; problem was not resolved. Thanks for taking my money. I'm bummed and with just a little less money in my pocket. Never again will I ever purchase another Whirlpool product. Or buy from your outfit again (because of the over priced part). I replaced a 25 year old 'working' General Electric fridge for this junk that sat in the warehouse for four years before this was delivered to me in 2018 and sold to me as a "new" appliance. This was found out only when it crapped out and I needed to have it checked out for repair. Oh yea, I only had the comment section and the part recommendation to go by, and the latest comments are at least two years old. I'll be surprised if this even gets posted.

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

Followed recommendations from others but went with most likely by percentage = defrost timer kit. Did not solve issue. Then went with bi-metal thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part ok. Then I saw on line that I should have listened for fan operation. I checked and found the fan motor to be defective. Replaced the motor and refrigerator worked fine. Both the motor and bi-metal thermostat were required. Should have checked fan operation first.

I replaced the relay started right up did fine for about 4 days. Came home from work I had lost everything in the freezer again.turned down the thermostat and back up and it started right up. 5 days later same thing again.

Remove rear panel with 1/4 nut driver. Pop plastic cover on compressor. Pry off relay and two wires and reinstall. Nice and easy and back to full function :)

Just replaced the old Push-On Start Relay and it started to work again.

I did a Google Search for a 1998 Whirlpool ED22RF, looked for trouble Isolation procedures. Don't remember the web sites but two parts were mentioned namely the timer and the thermal relay. After making sure it was unplugged I removed the back lower insulation panel, removed the red wire from the relay located on the left side of the condenser and unplugged the relay. I examined it for physical damage before checking with an ohmmeter and found the thermal relay sounded like it was full of sand when I shook it. So we found PartSelect and searched for the thermal relay and found an exact picture with the part number and ordered the part. We received the $30 part 5 days later. Only took 15 minutes and two tools to install. Thank you for saving us a few hundred dollars.

Replaced the start relay in about 5 minutes and plugged the fridge in and it started working. Easy repair to get fridge working again.