JSD2789AEW Jenn-Air Refrigerator - Instructions

First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!

Service and shipping were fantastic! I would definitely use Partselect again!

Removed the screws holding the housing inplace pulled and threw away than went to install the new drive motor but the screws were of a different thread so reinstalled the old motor and put the housing and bucket back together. after thawing out the water fill tube put it back into the cup-water fill and put clamp back in place. system is performing like brand new.

I removed the black drip grill and unscrewed the two screws holding the faceplate in place. After unplugging the faceplate from the dispensing unit, I removed the four remaining screws; be careful, one screw is shorter than the others.

I then pulled the dispensing unit away from the freezer door and removed the ice door assembly. WARNING: Make sure that you look carefully at the alignment of the return spring BEFORE you even touch it because as soon as I started using the needle-nose pliers to remove the spring, it shot across the room! Also, look carefully at how the end of the plastic rod fits over the old solenoid; in fact, look carefully at the entire plastic rod and how it aligns with everything!

Unfortunately, the pictures in the instructions are fuzzy so you can't really see how the spring is installed and how the plastic rod fits over the solenoid.

The solenoid was easy to remove and replace. Be aware that the plunger part of the solenoid slides in and out easily, so it's easy for it to fall out of the solenoid unit and roll away.

Once I had everything back where it was supposed to be, I screwed everything back in and the ice/water dispenser worked like new. I was even able to clean off some calcium deposits inside the unit while I had it opened.

If I have to do this again, I would estimate that it would only take 15-minutes or so. It took me longer because I didn't look at the alignment of the plastic rod in relation to all of the parts---that is one of the most important steps of this operation.

Anyone who is comfortable using tools and working with small parts should be able to complete this replacement project with minimal difficulty.

I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson

First I unpluged the frigerator, then I turned off the water. Then I removed the the black cover from the bottom back of the frig. The valves are located on the bottom right. Unscrew the bracket that is holding the two valves. I then removed the bottom valve from the bracket, unplug the electrical connections, and connect to the new valve.
To remove the water lines from the valves just move the white ring around on top of the valve and pull the line out and insert into the new one when ready. (the valves are the same colors) Do the same to the top valve, mount back to the bracket, then mount the bracket to the frig, hook up your water line to the valve, turn on the water and check for leaks, plug it in. Then put a glass under the water dispenser and try it out, it'll take a few seconds to get the water running through.
PartSelect was very quick on getting me my parts, TWO days, couldn't believe it. Very good examples of parts on web page.
Very satisfied and will use again.

removed outside water spill tray and removed exterior cover & interior cover exposing the door arm and solenoid. replaced with new parts including spring. Elontronics have a plug which is easy to disconnecct. & reconnect
old solenoid head would not have fit new door arm
and vice versa.
I strongly suggest using the kit.
A Torx type screw driver is required for all screws
on the Jenn-Air

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

I removed the one nut screw holding the Ice bucket shelf then removed the Ice Auger Container. Then I lifed the Part containing the Drive Motor. I removed the electrical connection which just plugs into the fridge. Once the Drive motor and container was out of the fridge I removed 4 screws and the Drive motor was out. I disconnected 3 electrical connectors and connected them to the new drive motor. Then replaced the motor and connected the 4 screws. I then installed the yolk on the drive shaft and then put the drive motor container back in the fridge and reconnected the electrical. Installed the nut screw and I was done.

I ordered the ice dispenser and selenoid door kit, it was easy to repair because I only needed the door. As per the instructions I removed about seven screws and disconnected the power source to the dispenser unit, pulled the unit out
and replaced the door in the two slots. Plugged the power source back into the slot, put the screws back in, now it works like new.
Thank you PartSelect, I received the part in just a couple of days. I recommend your service to everyone. I saved myself a lot of money and will order again on any needed
parts in the future.

where the wires crossed at the start relay, 20 years of vibration allowed them to short out and burn out the start relay ..since i have 2 identical fridges i switched the run capacitor to determine it was'nt bad too...ordered a start relay wednesday nite and got it friday morning...cold fridge by noon...good service and the part was exactly the same as the original....

I followed the instructions supplied by others on your site .They were right on. The repair was simple with the instructions. The service was absolutely superb. I ordered the part one morning.
The next morning Fed EX delivered the part to my door. I will use your site for parts from now on.

The factory installed fill tube was formed and molded, hard plastic. Nothing like the replacement part or the one depicted in the install instructions.To remove it, I had to grip the exterior water tube module with a pair of Visegrip pliers, twist and pull as hard as possible, to expose a section of fill tube. I then had to cut through the tube with a hacksaw to remove the module and flange that secure it to the access hole. From the inside, I removed the ice maker and fan shield to expose the remaining section of fill tube. Using a section of copper pipe and a hammer, I was able to drive the tube through the back wall of the appliance. Fitting the new tube was easy. However, it is too short to reach the fill cup. I fashioned a section of the old tube to create an extension which I inserted in the new part. And, much to my surprise, it actually works!

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

First pull the ice bin from the freezer. Then remove one screw that holds the ice maker in place. Rotate the ice maker to the right and up to release from posts on wall of freezer. Use a flat blade screwdriver at the front bottom of the white cover to pry the white cover from the ice maker body. Use teh flat blad screw driver to release the clip holding the wires to the ice maker. Remove a metal clip from the water receiver and transfer to the new icemaker. Transfer the ice sensing bail to the new ice maker. Install wires, front cover, hang on posts and reinstall screw to secure to freezer wall. Actuator pad requires you to first remove plastic cover over the top hinge of the freezer door. You must unplug the wire connector to prevent shorting out the printed wiring boards located behind the dispenser assembly. Then remove two screws and from the bottom carefully separate the dispenser from the door. The wires are not very long so don't just yank it out. The pad is easily removed and the new pad worked into place. Reinstall the dispenser into the door, reconnect the wires and reinstall the cover and you are finished.