JS48PPDUDB13 Jenn-Air Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- steven from long grove, IL
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker stopped making ice
Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from PELHAM, NY
- Parts Used:
- WP2198641
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Ice Maker cocker Bracket broken hinge
Easy repair. Remove 2 hex bolts. And remove.Install Bracket and replace 2 hex bolts and reinstall ice maker door to bracket. 10 minute repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from San Mateo, CA
- Parts Used:
- W11629974
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker quit making ice.
Removed the Wiring & Troubleshooting instructions from behind the front Grill and used to troubleshoot the KSCS25IN side by side refrigerator. I then removed the three screws from the Emitter assembly on the left side of the freezer. Then disconnected the four pin connector. Removed screw holding emitter PCB to housing and replaced with the new PCB and then re-installed. Similar steps for the Receiver assembly and PCB on the right side of the freezer. Unit started making ice after making some water level adjustments on the Timer assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gina from HAMMONTON, NJ
- Parts Used:
- WP2260518B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cap had broken notches
filter has to be removed and attached then inserted into rifrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from AVON, CT
- Parts Used:
- WP2260518B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter applicator broke
Bought new applicator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from CEDAR CREEK, TX
- Parts Used:
- WPW10191429
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Both Upper Lights Burned Out Same Time
The holder is held in place with two screws. Once you have it unscrewed you can snap the old sockets out and replace them.
Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.
Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from MEDWAY, MA
- Parts Used:
- W11629974
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker continued to make ice - would not turn itself off
followed the video provided on website. repair was very simple / straight forward. Once emitter and receiver boards were replaced, issue with ice maker was resolved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from ST PETERSBURG, FL
- Parts Used:
- W11629974
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No ice
Removed the cover plates and unplugged bad boards. Hard to plug in boards after attached to cover plates. Plug in boards first then attach to mounts. Ice in 4 hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from EL PASO, TX
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No Problem
Just needed to replace the water filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyner S. from MIDLOTHIAN, VA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Time to replace filter.
I pushed the lever on the filter located at the bottom of the refrigerator and it popped out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from KATY, TX
- Parts Used:
- WPW10546285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice Door Bracket Assemby failed resulting in Ice Door no longer opening and closing
With the freezer door closed, remove 4 screws around the ice maker door assembly. Open the freezer door and remove about a dozen small flat-head screws around the sides of the door that hold the stainless steel cover to the freezer door. No need to remove the very bottom screws if you have something to support the cover with. Remover 4 hex-head screws that hold the ice/water dispenser control pad in place, use tape to secure this pad to the freezer door so you don't have to undue all the electrical connections. Remove two screws that hold the Ice Door Motor & Bracket Assembly in place - disconnect the electrical connection for the assembly. Replace the new assembly in the opposite order it was taken off. Presto - done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from EASTON, MD
- Parts Used:
- WPW10191429
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lights failed despite new bulbs.
Used u-tube video to review steps in making repair. Wires shorter than described but after looking at replacement sockets difference was clear.
Was this instruction helpful to you?
Thank you for voting!