JS42PPDUDE01 Jenn-Air Refrigerator - Instructions

Did not have elec. schematics or instructions, thought the problem may be the emitter/receiver. Ordered these parts, and included in the package were instructions for testing the e/m bd. Followed instructions for testing the e/m and determined the e/m was OK. Did not remove the boards from the box. Checked the internet and found schematic for the ice maker, tested and determined the ice maker was faulty. Problem solved.

Being 50 miles from the Sears with a 7 year old unit, I actually changed out both board (a kit) which was 9 screws. 3 screws in the outside panels, and 2 in the larger board, and 1 on the smaller board. Both both boards plug in. I also changed the actual ice maker which unplugs and slides out on my unit. Remove a single screw (1/4") on bottom to remove a plastic shield that covers/protects the plug in. A plastic arm lock is in the bottom guide tray, push it up first. Then unplug the unit. Three more 1/4" screws in bottom to remove the custom plastic mount. Then reverses the process to install the new ice maker. Total $175 plus 1 hour labor. In 6 months the unit will have paid for the repairs. I hope to get 5 years of service from the job

First I removed the icemaker and the sensor boards by removing 6/7 screws. Next, I placed the new sensors into the emitter and receiver and re-installed the components...reset the icemaker and was all done!

Last time my icemaker broke I paid a contractor $225! This time I did it myself in 30 minutes and saved $150. And it was so easy my wife could'a done it......

A snap! The part arrived the day after I ordered it. (How, I don't know). The video showed exactly what to do. I did it. Ice maker now works like a charm. Thanks.

After calling Sears and setting up an appointment and waiting 7 hours for them not to show.. without any phone call..even after the dispatcher said I was "Next on the List" I figured thilure was the Emitter boards.. I ordered theere had to be a better way.. I researched this site and determined that the most likely cause of fa parts and received them within 3 days with standard shipping. I followed the optical diagnostic instructions that were included and replaced the boards. Within a few hours the ice maker was singing again.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

removed 3 screws on each side of freezer where the ice maker controls are unplugged the circuit boards. un screwed the boards from the plastic and put the new ones in, reinstalled. now, Ice and not over flowing! :)

I first ordered the electronic control boards. However, they arrived with an Instruction Sheet. The diagnostic procedures listed on that sheet identified that the optics were working properly, so did not use the electronics. That left the motor assembly as the culprit. Ordered that. The motor assembly arrived promptly and installed easily - just like the video. Ice maker began making ice immediately. Thank you PartSelect.

i replaced the electronic control board of emitter and receiver

Unplugged unit. Taped ice maker flap up and out of way. Removed screws holding emitter board, unplugged old board and connected new. Did same for receiver board on opposite side.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

My Ice maker would not release ice cubes, it thought the ice bin was full. So I got on You Tube and looked up how to videos. Partselect videos were the best that I found and the prices were low also. The whole repair took about 15 minutes.

I tried several things first : changed the filter cartridge, then the water control valve, then the control boards but still no ice. Rather than buy a new motor assembly, I bought a whole new icemaker which included the motor assembly and finally SUCCESS! In total it cost me about $350 but you have to try the easier and cheaper things first. One 1/4" screw and disconnecting the wire harness clip plus reusing the old icemaker base and the repair was complete. I would recommend a more detailed discussion on what each part does and the way the colored wires attach. Wire clips can sometimes be connected upside down. I was very happy with how quickly I received the new part. I whole-heartedly recommend PartSelect.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.