JFC2290VTB1 Jenn-Air Refrigerator - Instructions

Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues

Disconnect power to unit, shut off water supply, remove back panel change out valve, repeat steps 1-3 in reverse run water through system for about 5 min removing all air from lines

Let the ice in the freezer melt while installing P trap drain tube

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

The parts were very easy to replace, however I am still without ice and cannot figure out why. I have ohm tested the contol unit and everything works fine, I am able to jump it and turn on the motor and water fill valve. Any suggestions?...

Very easy to fix . It was harder to empty the contents out or the refrigerator than to repair . The diagrams on this site were very helpful in identified the part. and it was delivered in 5 days.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Snapped in new part

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

The Youtube Video was Extremely helpful--the model they worked on was a Whirlpool, and is held in with 1/4" machine screws. The KitchenAid is largely identical, but doesn't use screws. There is a plastic release you depress to free the Right Support from the cabinet. Otherwise, the process is identical to what's shown on the Youtube video. The Fridge "came with" when we bought the house, and we've already replaced the door seals using this website (another easy fix). Of course, when gently reinstalling the lid I snapped the pin on the Left Pantry Drawer support. So i've ordered that part too--i'll chalk it up to age/wear&Tear. The Left is much easier than the Right, as the Right Support has a sliding humidifier setting slide. So the Right is slightly more involved, but is also an easy fix. No tools required at all for either drawer support on the KitchenAid. Just be very patient and gentle as you re-install the drawer lid.

Part received was what I needed. There was one issue--the 'feed' opening to receive water and direct it into the ice tray was a side feed and what I needed was a back feed. That means I had to do some exchanging of parts to make it work. That exercise took more time that the actual installation.

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

Pull refrigerator out from wall to shut off water and power. Remove ice bin, pulling front down then out. Remove screw at bottom of icemaker, then pull down to release two clips, Pull out a couple inches to get hand behind icemaker to release wiring harness connector. (squeeze top and bottom to release clips). Remove unit. Remove wiring harness and wire bail from old unit and install on new unit. Reverse steps to install new unit. Make sure ice bin is fully inserted, or unit will not function.