JFI2089AEP5 Jenn-Air Refrigerator - Instructions

The toughest part was pulling the refrigerator from the wall....After removing the back-bottom access panel the compressor is right there with the Start-Dev and Cap..Took a few min to remove and install new parts....Very Simple and works great...no more clicking..

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

I unpacked the glass and slipped it into the shelf. Done.
What was more impressive was the delivery time. I ordered the glass at about 12:30pm one day and the glass was at my door by 9am the next morning. Even my husband was impressed with that.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.

1. Remove the crisper drawers from the refrigerator.
2. Remove the shelf from the refrigerator (a good opportunity to do some deep cleaning in the far reaches of the fridge ;).
3. With the shelf sitting securely on a flat surface, remove the old trim by using your fingertips to grab the underside of the trim and gently pull it away from the edge of the glass shelf. Work from one end of the trim to the other until the old trim pops off.
4. To attach the new shelf trim, push the trim gently onto the rounded edge of the shelf. Work from one end to the other until the trim snaps into place.

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

Thanks to others who shared their story, I was prepared to "muscle" the front cover off the old crisper and snap it into place on the new crisper -- warning if you are good with puzzles and mechanics, this repair is a "snap"; Pantry Lid is very easy, push pin on left side, slide old lid out and push new lid in.

The broken one just popped out and the new one popped right in! This company shipped out the part I needed immediately I had it in two days!! I highly recommend them!!

Easy repair, nothing complicated.

took out old lid, took out drawers above this drawer to make it easier to work on. installed new drawer simple by hand with no tools. put other drawers back. very simple no tools needed.

Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.

Easy