JCD2595WEP01 Jenn-Air Refrigerator - Instructions

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

this is the 2006 model.remove the bottom tray to access the two screws that hold the cover on then remove the screws.the cover will slide out but is kinda tight cause of the door handle but will come out without removing the handle.then open the door and turn off the ice maker and remove the ice bin.there are two bolts to remove with a 1/4 inch nut driver to remove the plastic piece. you can then remove a metal piece and spring that sits on the drive shaft. i used a pair of needle nose pliers to remove the drive shaft cause my fingers were too big to fit in the hole.close the door and go back to the panel.there is a cardboard protector that you lift up to expose the motor.the motor sits on a plastic motor mount with two bolts you can remove with a 1/4 inch nut driver. it slides out and you can unplug the wire clip. remove the motor. remove the four bolts that hold the motor to the motor mount then mount the new motorthen put it all back together. it might be a good idea to unplug the fridge before this process. i didnt and when i tested the the ice and water,the water would not shut off. i had to open the door to get the water to shut off then push and hold the reset button to get it to work properly.

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

I pushed the lever on the filter located at the bottom of the refrigerator and it popped out.

trashed old one, slipped new one on.

Just needed to replace the water filter

followed the video provided on website. repair was very simple / straight forward. Once emitter and receiver boards were replaced, issue with ice maker was resolved.

Removed the cover plates and unplugged bad boards. Hard to plug in boards after attached to cover plates. Plug in boards first then attach to mounts. Ice in 4 hours.

The holder is held in place with two screws. Once you have it unscrewed you can snap the old sockets out and replace them.

Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.

Unscrewed Phillips screw from bottoms of ice container where the piece broke and installed new piece with old washers in place. Placed Phillips screw back in

Looked up the part on the partselect diagram, ordered it and it came really quickly. Popped the broken ones out and put the new ones in. It took me longer to take the contents out of the shelves in the door, than it did to fix the shelves!
I had ordered two, only one came. I called and the lady was WONDERFUL to deal with, she cross checked it and said there must have been a mix up in the factory. (Totally understandable—things happen). She rectified the situation quickly and the following day, the other part was on my doorstep.
I really like this company’s response in having and delivering any parts I have ever ordered. Now I think of them first before thinking I have to replace an entire machine.

Slapped it on with the Palm of my hand and slid it back until it reached the end of the slot. Replaced deli drawer. Took all of 30 seconds.

Remove ved shelf to gain access to small panel on inside of freezer door just above shelf. Removed two screws in panel using 1/4 inch nut driver. Disconnected old auger motor and removed 4 screws holding it in place. Removed old motor from shaft and replaced with new one. Reconnected new motor with screws from old motor. Replaced panel and shelf. Refrigerator now dispensing ice again. Very simple fix and cheaper than repairmen coming out.