JSD2789ATW Jenn-Air Refrigerator - Instructions

First I unpluged the frigerator, then I turned off the water. Then I removed the the black cover from the bottom back of the frig. The valves are located on the bottom right. Unscrew the bracket that is holding the two valves. I then removed the bottom valve from the bracket, unplug the electrical connections, and connect to the new valve.
To remove the water lines from the valves just move the white ring around on top of the valve and pull the line out and insert into the new one when ready. (the valves are the same colors) Do the same to the top valve, mount back to the bracket, then mount the bracket to the frig, hook up your water line to the valve, turn on the water and check for leaks, plug it in. Then put a glass under the water dispenser and try it out, it'll take a few seconds to get the water running through.
PartSelect was very quick on getting me my parts, TWO days, couldn't believe it. Very good examples of parts on web page.
Very satisfied and will use again.

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

removed outside water spill tray and removed exterior cover & interior cover exposing the door arm and solenoid. replaced with new parts including spring. Elontronics have a plug which is easy to disconnecct. & reconnect
old solenoid head would not have fit new door arm
and vice versa.
I strongly suggest using the kit.
A Torx type screw driver is required for all screws
on the Jenn-Air

I removed the one nut screw holding the Ice bucket shelf then removed the Ice Auger Container. Then I lifed the Part containing the Drive Motor. I removed the electrical connection which just plugs into the fridge. Once the Drive motor and container was out of the fridge I removed 4 screws and the Drive motor was out. I disconnected 3 electrical connectors and connected them to the new drive motor. Then replaced the motor and connected the 4 screws. I then installed the yolk on the drive shaft and then put the drive motor container back in the fridge and reconnected the electrical. Installed the nut screw and I was done.

I ordered the ice dispenser and selenoid door kit, it was easy to repair because I only needed the door. As per the instructions I removed about seven screws and disconnected the power source to the dispenser unit, pulled the unit out
and replaced the door in the two slots. Plugged the power source back into the slot, put the screws back in, now it works like new.
Thank you PartSelect, I received the part in just a couple of days. I recommend your service to everyone. I saved myself a lot of money and will order again on any needed
parts in the future.

where the wires crossed at the start relay, 20 years of vibration allowed them to short out and burn out the start relay ..since i have 2 identical fridges i switched the run capacitor to determine it was'nt bad too...ordered a start relay wednesday nite and got it friday morning...cold fridge by noon...good service and the part was exactly the same as the original....

The factory installed fill tube was formed and molded, hard plastic. Nothing like the replacement part or the one depicted in the install instructions.To remove it, I had to grip the exterior water tube module with a pair of Visegrip pliers, twist and pull as hard as possible, to expose a section of fill tube. I then had to cut through the tube with a hacksaw to remove the module and flange that secure it to the access hole. From the inside, I removed the ice maker and fan shield to expose the remaining section of fill tube. Using a section of copper pipe and a hammer, I was able to drive the tube through the back wall of the appliance. Fitting the new tube was easy. However, it is too short to reach the fill cup. I fashioned a section of the old tube to create an extension which I inserted in the new part. And, much to my surprise, it actually works!

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

First pull the ice bin from the freezer. Then remove one screw that holds the ice maker in place. Rotate the ice maker to the right and up to release from posts on wall of freezer. Use a flat blade screwdriver at the front bottom of the white cover to pry the white cover from the ice maker body. Use teh flat blad screw driver to release the clip holding the wires to the ice maker. Remove a metal clip from the water receiver and transfer to the new icemaker. Transfer the ice sensing bail to the new ice maker. Install wires, front cover, hang on posts and reinstall screw to secure to freezer wall. Actuator pad requires you to first remove plastic cover over the top hinge of the freezer door. You must unplug the wire connector to prevent shorting out the printed wiring boards located behind the dispenser assembly. Then remove two screws and from the bottom carefully separate the dispenser from the door. The wires are not very long so don't just yank it out. The pad is easily removed and the new pad worked into place. Reinstall the dispenser into the door, reconnect the wires and reinstall the cover and you are finished.

I reasoned that the water-value was caked with hard water deposits, or perhaps just worn out. I traced the plastic water line to the back of unit, then found the double water valve. I was not "sure" that this was the problem, but I order the part any way and it fixed it!! The removal /installation was pretty easy. First turn off the water supply to the unit. Then loosen and remove the incoming copper pipe from the unit. Remove just two 1/4 in. hex head screws and carefully pull the unit out a bit. Then remove the electrical connectors and the plastic tubing connectors. Just do the reverse to install it. I am very happy with the item ordered from PartsSelect. Perfect. And shipping time was fast too. Thanks guys.

First removed the old water filter and replaced it with the filter bypass. Very simple and no tools needed

Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.

First I compared the old parts and new parts to see if I had ordered the right thing then I inserted the new stop into the door. Since the stop has a lip that needs to fit into the slot I the door, I used a hammer to push the part up so it would lock into the hole. Very Simple

Removed the light bulb and shield, no tools needed.

Removed the bottom shelf of the refrigerator and the top meat drawer. My 12 year old inserted the light bulb and shield, then we replaced the shelf and drawer.

Very easy.