JS48PPFXDA Jenn-Air Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Brentwood, TN
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
It was time to change the water filter.
All work was done by hand. I removed the cover plate, unscrewed the existing water filter and screwed in the new one. I returned the cover plate to its original position and bled the air out of the line by running the water dispenser for a few minutes. It could no have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Pleasanton, CA
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed to be replaced in the fridge
Located the filter, removed the filter, installed the new one, reset the filter light on the front of the water discharge, and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Des Moines, IA
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old water filter
Removed by hand the old water filter and installed the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from MELBOURNE, FL
- Parts Used:
- W11342242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no shut-off for ice production; shut-off arm broken/missing
Inserted the prongs of the replacement shut-off arm in the holes provided in the bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from PITTSFORD, NY
- Parts Used:
- WPA3073101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
No problem
I had a son put in the new light bulbs. Rather simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary L. from Millsboro,, DE
- Parts Used:
- WP627843
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Berkeley, CA
- Parts Used:
- WP628356
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Ice maker broken. Quick fix
The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.
The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.
Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.
Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!
The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.
Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.
Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conrad from MEDINA, MN
- Parts Used:
- 67001454
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Lower bushing in hinge fractured, resulting in squeaking door
Remove upper hinge with socket set. I found it helpful to remove the door spring (on bottom of door) in order to be able to lift out the door from lower hinge. Replace bushing. Replace door, upper hinge, you're done. I did note that lower hinge post (~10mm OD) had worn against the frame due to the loss of bushing, losing ~1-2mm of metal. Would not have seen this until the door was off. Was concerned this will lead to premature failure of the new bushing, but it will be a much harder job to replace lower hinge (looks like I will need to empty and tip the fridge to access lower side), plus I didn't have the lower hinge part handy (~$40-45), so I will replace both if the bushing fails again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from WESTFIELD, IN
- Parts Used:
- WP628356
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
broken hinge bearing on ice maker
Disconncted power, pulled plug on disconnect, loosened 3 ice maker attach screws, removed ice maker. carefully removed old broken part, to understand reasembly. Reinstalled new water fill & bearing part.. hung icemaker and tightened attach screws. Reattached electrical plug.. turned on power, it all worked. .took about 45 min to remove, 15 min to reinstall. Right tools needed re disassembly AND ASSEMBLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Discovery Bay, CA
- Parts Used:
- WP2182124
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The ice stripper cracked from freezing.
There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Orleans, MA
- Parts Used:
- WP628356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice maker arm mount
Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.
It would have been $150& $50 for visit to replace ice maker unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Belfast, ME
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter expired
My husband did the replacement of the filter, so it was really easy for me. Easy for him too! The best part was this company had the best price, and the part was here in no time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Rancho Mirage, CA
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
annual replacement
have always done it myself, but Maytag store closed, so I didn't know where to purchase filter
I received it from Parts Select, in 2 days and if I remember right, price was cheaper than I paid last year, at store.
I received it from Parts Select, in 2 days and if I remember right, price was cheaper than I paid last year, at store.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pandora from North Ridgeville, OH
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water Filter Replacement
Just a filter replacement -- however more impressed with the speed of which I could receive the replacement.
Can't find them anywhere local -- glad I found Part Perfect!
Can't find them anywhere local -- glad I found Part Perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Rio Rancho, NM
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter was one year old and needed to be replaced
Open refridgerator door, remove old filter by hand in a counterclockwise direction. Insert new filter turning clockwise. Close refridgerator door and fill a glass with water from dispenser. This will remove air and ensure water to free flow. Check for leaks.
Was this instruction helpful to you?
Thank you for voting!