JS48SEDBDA Jenn-Air Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Matthew from Menifee, CA
- Parts Used:
- WP61003336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Old plastic ring was damaged due to leaking icemaker causing door to open when ice dispensed.
No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hank from Alpharetta, GA
- Parts Used:
- 61003791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter costs ridiculously high!!!
Replaced filter with by-pass plug. For some reason though, ice maker does no longer functions, although there is flow out of the cold water tap. Is the design of the bypass plug such that, when installed, it impedes flow to the ice-maker?
Thanks
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Newton, NJ
- Parts Used:
- 61003803
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The solenoid from that operates the fountain went south
I ordered new solenoid that came with door. I installed it and it was making a very loud buzzing noise. I also had a frost buildup between the icemaker and the icemaker chute in the door. I posted my problem on the forum and Sheila suggested that the heat from the defective solenoid might have distorted the fountain housing, causing the new solenoid not to seat right, and possibly letting outside air into the icemaker. On closer inspection I saw that the hosing WAS distorted. I ordered a new one, installed it, problem solved! Hats off to the staff here, where else can you get a diagnosis first -so you know what parts to order!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KELVIN from SOUTHFIELD, MI
- Parts Used:
- WPA3073101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light blew out
change light bulbs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- veso from Macomb, MI
- Parts Used:
- 67001454
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Grinding metal sound when opening refrigerator door.
Removed screws from upper hinge. Removed washer from door stopper on bottom hinge. Lifted door off lower hinge. Replaced bushing.
Took about 15 minutes and cost less than $12. Service call alone was going to be $70.
Took about 15 minutes and cost less than $12. Service call alone was going to be $70.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Fayetteville, GA
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the water filter for the refrigerator
I watched your online video on how to take out the old filter, and then to replace it with the new filter. It was as easy as on the video. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Highland Village, TX
- Parts Used:
- 61005520
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice dipsenser was malfunctioning
Viewed the repair video. Removed covering. Replaced limit switch, control board, and solenoid. Very easy repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Newark, DE
- Parts Used:
- 61005844, WP61005253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
seloniod failed and ice maker only made crushed ice
Removed screw onder on left side of ice maker shelf. Then removed shelf while disconnecting the wires behind. Removed selonoid and yolk and simply reinstalled in reverse order. The customer service was great because I first ordered the wrong part and was easily returned and correct part sent. If you are ordering and have questions call them. If you sense your agent doesnt have the full knowkedge you need I would ask for another one. This is why my original part was wrong. They handled my problem and I was pleased.
Alan
Alan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GOSHEN, IN
- Parts Used:
- W10156818
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wife used vacuum cleaner and busted blade off fan
Instructions were great five minutes to remove and replace fan....Thank You............ saved big money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Newport News, VA
- Parts Used:
- 61005520
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The ice door wouldn't open.
I followed the video of your repair man. Made it very easy.Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Richmond, VA
- Parts Used:
- WP61003336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Ice Maker couldn't drop ice through the door.
I pulled the drive ring off of the icemaker and replaced it with the new part. Saved a $150 service call plus cost of part. It cost me a little over $11.00 and a repairman probably would have charged $30.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Des Moines, IA
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old water filter
Removed by hand the old water filter and installed the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Pleasanton, CA
- Parts Used:
- EDR7D1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed to be replaced in the fridge
Located the filter, removed the filter, installed the new one, reset the filter light on the front of the water discharge, and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Westcliffe, CO
- Parts Used:
- 12001773
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
all 8/32 and holes should have been tapped
had to saw off the shaft to get the yoke off and tap the holes for the 8/32 screws. all holes should have been tapped by the factory. Other than these problems, everything else went pretty good.
Was this instruction helpful to you?
Thank you for voting!