JS48CXDBDB00 Jenn-Air Refrigerator - Instructions

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

removed the LED covers on both sides of the freezer, unplugged each circuit board, plugged in both circuits, replaced the LED covers, job complete, making ice

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!

Sorry I didn't do the repair but my husband did. It took him about an hour and a half. He did have to take the main part of the ice maker out of the fridge and take a couple of pieces off t oslide the tabs from the stripper arm into place. It was great. Fixed the icemaker for $22.00 dollars with no service fee. I can't imagine what they would have charged me.

Had to widen screw access hole in motor frame enough to use the phillips bit with my 12V impact driver. That worked perfectly. It took an extra two hours of trying to break the screw free without stripping it and figure out what to do when it wouldn't budge. Once I got the screw out the fix went quick and the ice maker now works great. If you have a coroded screw go straight to the impact driver.

Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.

The emitter code: Hold the flap that covers the receiver. (On the left) If the emitter does not stay red, the emitter and receiver are defected.

Replaced the emitter and receiver board

Unplug the refrigerator:

I first removed the ice-maker service door by removing the 2 screws at the top. Next, I removed the 3 screws on the lift side that housed the receiver. It is close, so remove the 1 gold screws on the receiver. This will allow you to separate the switch without any damage. Plug the new receiver in and reverse the process. Put the gold screw in to secure the board. Replace the 3 screws back into the receiver panel.

Remove the 3 screws on the right side. The emitter has 2 gold screws. Remove them so I could separate the switch. Plug the new switch in and replace the 2 gold screws.
Place the 3 screws back into the right side panel.

This process took roughly 30 minutes. After assembly, the ice make was dropping ice in 30 minutes.

There are several large parts places in my area but I saved about $35 by ordering online.
I place my order on Friday morning and the part was in my hands Saturday @ 6: 30 PM the next day.




Oliver of Riverdale, Ga

Called a repairman out. For $125 he told me what I already knew! The ice maker wasn't working. Said I needed new emitter boards and ice maker. Would go back to the shop and call me with an estimate. Estimated parts were $330 plus another service call to put them in.
Went on line and found PartSelect. Emitter boards were $87+shipping. Ordered. Arrived in 3 days. 3 screws on each side. Unplugged old boards. Plugged in new. 15 minutes. Still did not work. Took out ice maker and examined. Gear that drives ice ejector fell off. End of shaft broken. Ordered new motor unit from PartSelect. $61+shipping. Arrived in 2 days. Loosened 1 nut screw. Slid ice maker out. Unplugged. Removed motor cover. 3 screws removed motor. Replaced with new motor and reassembled. 15-20 minutes max.
3 hours later had ice coming out for under $160. Wish I had known sooner. Thanks PartSelect.

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.

Removed the cover plates and unplugged bad boards. Hard to plug in boards after attached to cover plates. Plug in boards first then attach to mounts. Ice in 4 hours.

I pushed the lever on the filter located at the bottom of the refrigerator and it popped out.

Just needed to replace the water filter