JS42CXDUDB00 Jenn-Air Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from Cary, NC
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice would not fall from ice maker
I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVE from HUGHESVILLE, MD
- Parts Used:
- WP2260518B
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Part imediately broke
Dog chewes up the original part. Got the replacement , put it on the filter turned to lock in place and tried tp pull out old filter ( same procedure has been done multiple times successfully) part broke instantly upon putting pressure tom pull out filter. Sent back to you the next day for replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Tyler, TX
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter needed replacing
followed the instructions on the box
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Pryor, OK
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Following a brief power outage, it stopped producing ice. Harvester was at 6:00 with fingers frozen in ice cubes. Would make a batch if I freed the harvester and jumped the t-stat, but would quit again.
Unplugged refrigerator. Used nut driver to remove small bolt retaining wire cover on right side of ice maker. Removed wire cover, used flat head screw driver to depress side-rail clips. Ice maker slid out, unplugged. Timer module cover pops off easily. Three screws removed the timer module. Installation was reverse of removal. Had ice in less than an hour, bin was full by next morning. If you have a screw driver and know what it's for, this job should come easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Rutherfordton, NC
- Parts Used:
- WP4373559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
coupling on water line thru freezer door cut due to moving Refg and having to remove doors.
Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bill from escondido, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
light inside fridge was flickering and clicking
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
Was this instruction helpful to you?
Thank you for voting!
Ice maker auger motor runs but wouldn't dispense ice
My Kitchenaid side by side freezer has an ice dispenser on the door that would not dispense ice. The electronic door opened and the motor would come on with a repeated clicking noise. The Auger would turn with a few ice cubes in the bin, but not under load. After ruling out a clogged chute, I figured that the motor was stripped. The rod that turns the auger is a hexagon shaped piece, much like a screw driver you would use with your drill. After years of breaking down ice, it stripped the hexagon key in the motor, and would just spin under load. Now, PAY ATTENTION TO THIS PART. I looked online for a repair and saw a very similar motor repair that involved taking off the front panel and electronics. I did this, and ran into a solid piece of plastic with no way to get to the motor. I then looked at the inside of the freezer door more carefully. About 2/3 down I saw a small panel held in place by four 1/4 inch hex nuts. What was a 15 minute job, cost me over an hour removing and replacing the front of the freezer. Anyway, the replacement motor fixed the problem without a hitch, and now we have ice. Of note, this is the second repair of this ice maker system, after first having to replace the ice maker itself. And, this the second Kitchenaid built in refrigerator of this model as our first had ice maker issues and was returned as a recall. It is only 5 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Shakopee, MN
- Parts Used:
- WPW10190929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice stuck in mold. mold coating was peeling off.
Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Aledo, TX
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
icemaker quit working
removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories about those guys!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sandra from mechanicsville, VA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
ice dispenser broken
ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically inclined,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Aurora, CO
- Parts Used:
- WP628356
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken cup water fill on ice maker
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
Thanks,
Matt
Thanks,
Matt
Was this instruction helpful to you?
Thank you for voting!
The ice maker in the door wouldn't dispense ice.
i took the cover plate off the inside of the freezer under the ice bin[two screws] then I disconnected the wiring harness, then removed the four screws to remove the motor and then put the new motor in and the ice dispenser dispensed ice. Less than 1/2 hour with only needing a nut driver,and a flashlight.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Hoschton, GA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
It was just time to replace the water filter.
We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from STOW, OH
- Parts Used:
- WPA3073101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burnt out bulb
took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks
lost the owners manual,
part select's schematics were very helpful
thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Ann Arbor, MI
- Parts Used:
- WP2266802
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Switch went bad
Our unit is a built-in unit so first had to remove the decorative cover panel to expose the internal on/off switch. Turned off the circuit breaker. Disconnected the wires (simple pull-off/push-on). Removed the old switch which meant clipping the plastic tabs holding the switch in position. Inserted the new switch by simply pushing it through the opening being sure to have it in the same alignment ('off' to the back of the unit.) Reconnected the wires making sure to have a white ground wires on the left and the black 'hot' wires on the right. Turned the circuit breaker back on. Turned the switch on. Now it runs.
Was this instruction helpful to you?
Thank you for voting!