JSD2488DEW Jenn-Air Refrigerator - Instructions

First I compared the old parts and new parts to see if I had ordered the right thing then I inserted the new stop into the door. Since the stop has a lip that needs to fit into the slot I the door, I used a hammer to push the part up so it would lock into the hole. Very Simple

Removed the light bulb and shield, no tools needed.

Removed the bottom shelf of the refrigerator and the top meat drawer. My 12 year old inserted the light bulb and shield, then we replaced the shelf and drawer.

Very easy.

First I removed the top hinge cover plate. Then removed the three screws in the top hinge. I lifted the door off the lower hinge and laid the door on the kitchen counter. I removed the one screw holding the natural door closer part from the bottom of the door and installed the new part with the same screw. I then replaced the lower hinge pin with the new one. It just sets in place. I then repositioned the door and reinstalled the top hinge. the whole job took about 15 minutes after the refrig door had been emptied. The door works like new.

Removed shelf, removed 2 screws, pulled off face plate. Removed electrical connection to circuit board. Removed 3 screws holding part in place and pulled forward. Replaced door flap easily. Hardest part was getting dispenser mechanism back in place with the water tube routed through the right spot.

Followed the directions included with the parts, which were exact and well illustrated. If you are comfortable working around circuit boards and electrical connectors (with the power OFF, please!), then you can do this repair. Why electronics on this repair? Because you have to unplug a board to get to the parts, and disconnect the connectors to the solenoid. But again, the directions were fabulous, and I'm almost looking forward to needing to use PartSelect again. Almost.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

This is an easy repair. It took me longer to remove the bins off the inside of the door and clean then up, then the actual repair. Remove the top hinge trim 1 Phillips screw. After the hinge trim is removed you'll see 3 hex screws. Remove the 3 screws. Hold and open the door half way, and lift up on the door. The door is not heavy. Use your kitchen table as a work bench. Place the door flat on the kitchen table . On the bottom of the door you'll see the "CLOSER" One screw removes it. Reverse operations and reassemble. Note: Put a little Vaseline grease on the pivot point. Thats it ... 15 minutes and your done plus you saved a $65.00 service call.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Simply cut the water tube on both sides of connector and push in the new one.

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

replaced the defrost heater assembly and it solved the rpoblem

Maytag wide by side refrigerators tend to eat these parts about once a year, and this is my third assy so the replacement went very fast. When we used the Maytag warranty they replaced this part about 6 times, after they exchanged the refrigerator. No major disassembly is required, drop the plastic after removing a few screws, plug in the assy, and you are good to go, no more frozen food in the refer. The only tricky part is getting the clips to release so you can slide the plastic cover forward, but after a while they break off and it is easier to remove.

First I unplugged the refrigerator. Next item was the ice-maker; remove (3) screws and unplug it from the back wall. Third task is remove the (4) screws that attach the back wall of the freezer compartment. Lift the wall up enough to dislodge the center cooling shaft that the fan rides in and remove the rear wall. The last item is the fan motor which is attached to the freezer wall by (2) screws and (3) wires which are easily removed. Change out the motor and reassemble freezer compartment .

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes