IPT104302 Inglis Refrigerator - Instructions

I found the evapoator iced over and the evaporator fan not working . I tested for voltage on the fan circuits ,found them to be good .ordered the part i needed and repaired the fridge . in the meantime until i recieved my part i put a small fan in the freezer to keep the evaporator form icing over so my food would not spoil .

After removing two rear plastic panels, (very easy). The fan is easily accessable. Two more screws to remove the fan brace and remove three wires from the fan and its out. Reverse the process and its finished. The propellor is not part of the fan motor order and you can remove the old propellor and put on new motor (easy). One step that is not accounted for is the removal of a flexable plastic "nut" on the fan shaft. This piece holds and connects the fan to the fan brace. You will understand this when you compare the new fan with the old and see the plastic "nut" sleeve on the old fan. Simply pull it off and put on new motor shaft (it simply slides on and off the shaft).

I unpluged fridge then took the cap off the fan moter then took the three nuts off the fan then unplugged the three wires. And visaversa, ta! Ra! Fridge works just like new.

Unplugged the refrigerator and then unloaded the freezer. removed the panel at the back of the freezer to expose the fan. Carefully unclipped the wiring harness and then removed the fan motor. Swapped the fan from the old motor to the new one (I did use a hair drier to warm the plastic fan to make it easier to remove) and reassembled the fan and panel. Simple and easy, and now the refrigerator works just like new.

I watched the repair video. My son followed my instructions. He removed the ice-maker. The back panel was frozen, so we chipped and waited for the ice to thaw. There are three wires to remove from the old fan. My son used his cell phone to take a picture of the correct wiring. He used needle nose pliers to get the motor off the bracket. I used hot water to thaw the ice, so we could get the back panel to fit properly. If we weren't waiting for the ice to melt, we could have finished in about a half-hour. I'm 86 years old, and have carpel tunnel. My son is 63. Together, we make a good team.

I replaced broken fridge with a spare fridge; mean while I went online and did research and came across "Parts Select" which was extremely helpful with similiar situation and helpful guidance. $80 and fridge is as good as new.Thank you.

I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

I was careful to unplug each cord one at a time so that I can easily match them up to the new start relay. Once I got the cords plugged into the new start relay, I went ahead and plugged in the fridge and it worked like it never stopped working. I must admit, I'm still nervous about this fridge because I never had to do anything like this in my life so in the back of my mind, I'm always wondering if I did it correctly or not. I was giving a lesson on how to make sure that I have it on correctly but that didn't put me at ease..lol. Parts Select sent this part in less then a day and that made me appreciate there business even more. I was concerned that the part wouldn't get here until later on that week.

I replaced the relay started right up did fine for about 4 days. Came home from work I had lost everything in the freezer again.turned down the thermostat and back up and it started right up. 5 days later same thing again.

Looked at your You Tube video and followed the instruction

1. I removed the plastic back cover panel in the freezer. 2. Took flash photos with my phone of the motor and wire configuration. 3. Removed noisy Evaporator fan bracket from freezer. 4. Removed Fan Blade from old Motor. 5. Removed old Motor from Bracket. 6. Installed New Motor into the bracket. 7. Installed the fan blade onto motor spindle. 8. Installed the bracket onto the back wall of freezer. 9. Noticed that the tab for the ground wire was inaccessible. 10. Cursed like Linda Blair in the Exorcist for about 5 minutes. 11. Repeated steps 3 - 5... 12. Unscrewed the ground tab and placed it on the opposite side and screwed it back in. 13. Repeated steps 6 & 7.... 14. Tried to install the bracket and motor back onto the freezer but the bracket screw holes weren't lining up. When I removed the motor to flip the ground tab over, I reinstalled the motor onto the bracket upside down. 15. Tear some hair out of my head. 16. Repeated steps 4 & 5 and flipped bracket over. 17. Repeated steps 6 - 8... 18. Placed wires onto tabs. 19. Ground wire would not stay securely onto the tab. 20. Slightly opened up metal fastener of ground wire with needle nose pliers and stuck it onto the tab. 21. Still not on there super tight. I gave up wrestling with it and just prayed it will stay on there anyway. 23. Turned on freezer to check if it works. 24. Reinstalled plastic back plate. 25. Put melted food back into freezer.

took a voltage check to ensure had 120vac to the motor and did. Ordered new evap fan motor, installed, refrig works as good as ever now. Thanks for your website.

I looked at the parts diagram from partsselect.com and watched the short video. This was a huge help and made the installation of the new part actually easy. I removed the thermostat control panel from the top portion of the refrigerator side with a 1/4" nut driver and then removed the defrost control board with a philips head screwdriver. I then replaced the part and put everything back in place. The only problem I had was trying to get the thermostat control panel back onto the front clips.I would recommend partsselect.com to anyone. The refrigerator/freezer works great now. Thanks again. Chris