IKS203303 Inglis Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joseph from North Palm Beach, FL
- Parts Used:
- W10822259
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Motor Bearings Locking Up
Removed the back panel on the refrigerator--unplugged the condenser fan motor--removed the motor--placed a small fan to cool the condenser--called parts select--ordered the motor--the motor arrived less than 24 hours after I ordered it--replaced the motor and rear panel on the refrigerator--probably saved more than $200. 00--Very happy with parts select service--plus I had a misunderstanding with my credit card and john at parts select was very helpful --not their fault--excellent company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from North Port, FL
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken drawer
replaced
Was this instruction helpful to you?
Thank you for voting!
Crisper crac kerd and there was no glass insert cover
It took me less than 5 minutes and I had everything installed myself. thanks for the help in ordering the right parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roberto from san Antonio, TX
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
freezer gets too cold then gets to regular tempetured
disconect the power removed the screws with the phillips screwdriver removed the front cover and then removed the rest of the screws. removed the three covers and then removed the thermostat. replaced in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Kansas, OK
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Freezer wouldn't defrost/low temps in refrigerator
Found the housing for the thermostat; took housing apart pulled out thermostat and took off the hose put the hose on the new thermostat installed new thermostat and replaced housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from NAYLOR, MO
- Parts Used:
- WP2188664
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crack in vegetable drawer
Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee
Was this instruction helpful to you?
Thank you for voting!
My Crisper Draw side railing had broken
I ordered the 2 new drawers, the crisper pan and the meat pan with handle. I took them from the box, wiped them out and slid them right into the spots where my previous drawers were. End of story. This took less than 5 minutes to install. I used the chat feature to inquire as to what number items that I needed to order these 2 drawers, was given the numbers and order the items on line right then. Easy They arrived in record time, like maybe 2 days. They were well packed and arrived in pristine condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lewisville, TX
- Parts Used:
- WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Refrig Door Cams wore out and made noises when opening and closing.
Followed Door Removal instructions by removing the Top Screws from the Cabinet. Lifted Door OFF the Metal Hinge. Unscrewed both Lower and Upper Cams from the Hinge and Door. Replaced with new after coating with Vasoline. Lifted Door back in place with help from Wife. Only problem was guiding the Door back onto the Hinge. Works fine. Two year old Frig. This is a design problem, as the cams should last longer than 22 months.
Was this instruction helpful to you?
Thank you for voting!
Fan motor was making noise.
First I removed all food in freezer.Then removed selves and hanger brackets.Then the back panel and light cover.Then I unplugged motor but before this I unplugged refrigerator from the wall.Removed motor from bracket after pulling of fan. Reversed the order to install motor and put back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clive from parlin, NJ
- Parts Used:
- 2159073
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
old gasket was not sealing door would open when freezer door closed
remove door pull gasket out put new gasket in replace door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from San Antonio, TX
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Heathsville, VA
- Parts Used:
- W10508993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Crisper drawer tilted to the right when pulled out
The repair consisted of lifting up the drawer cover and replacing it. Why the 60 minutes to do that? It took 58 minutes to clean the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duncan from Metairie, LA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jairaj from North grafton, MA
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The refrigerator door was hanging low and not closing properly. Hence the refrigerator was not maintaining the temperature
First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly.
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Eaton Rapids, MI
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The frig/freezer shut off too often and would not stay cold.
The new thermostat assembly installed quite easily, just a couple of screws, but the thermostat probe however was kind of a pain in the rear. The probe is about 3 feet long and you have to remove a plastic sleeve from the old part and re-install on the new probe, it fits very tight and takes some time to do. Overall it was a very easy fix.
Was this instruction helpful to you?
Thank you for voting!