CSF24EMD Hotpoint Refrigerator - Instructions

It took longer to remove the ice bucket and frozen food than it did to replace the ice maker. Remove one screw with a 1/4" nut driver, slide outward and remove plug. transfer water tube to new unit. plug it in, slide into rear slots and install one screw. Replace ice bucket and frozen food, shut the door and hear ice falling in about 30 min. Easy job! Great product! THANKS MJS

I ordered the replacement from you guys, got the new ice maker and the plug had an adapter, but it wouldnt fit in with everything. So I cut the plug off my old ice maker and put it on the new one and it works just fine.
thanks for everthing P.S. i got the ice maker from you for 109.00 and sears wanted 130.00 for it
good stuff good deal.

Used the nutdriver to loosen two screws, life out ice maker, disconnect electric plug and put aside. Placed the new icemaker on the loosened screws, plugged in electric connector and tightened screws. Used small level to verify that unit was level.Waited about two hours for first cubes to be released into tray - has been working fine since!

The instruction video was great, mine was easy than even the video showed it to be. I changed it out in less than 15 minutes and it works great. The niocve things I didn't have to wait for a repairman or my husband to fix the problem.

REplaced old icemaker with a new one. Install simple, However that was not the problem. I then replaced the water valve. Still no ice. I check the electric connection was OK. THe problem was the elbow fitting on the top back of the refrigerater leading to the icemaker was blocked with ice.Cleared it and turned water faucet up all the way. Ice maker worked.

The video on the site was very helpful. The repair was really easy. It was exactly the way the video showed how to do it. I would definitely use this site again to find parts, figure out the "how-to", and use for skematics of appliances. Thanks.

turn off water. turn off electricity. empty freezer section of frozen food. remove ice bucket. loosen two screws holding IM to wall of refrigerator. lift off icemaker, and then unplug it as you remove it. INSTALL new IM by: putting new water funnel onto new IM. attaching adapter cord to IM. plug in IM electrical cord to refrigerator and then hang the new IM onto the two loosened screws on the refrig wall. Now tighten the two screws. the extra adapter electrical cord hangs below the new IM, but does not get in the way when you reinstall old ice bucket. reload food, turn on elec and water. PS. i had a crack in the casing of the new IM, so i got a new one, but that one was cracked too. so i just installed the second cracked one. hope it is not a problem.

Watched video on website then removed old ice maker. New one went in without any problems. Working great. I am a 60 year old woman and had never done anything like this but so easy. Husband scared now, doesn't know what project I will take on next.

install icemaker water was allways delivered to previous unit water is not being delivered to icemaker still having difficulty

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0