CTX18GFC Hotpoint Refrigerator - Instructions

Could not have been easier. Trick was finding the part for a refrigerator this old, probably more than 20 years.
1. Removed crisper bin. Removed broken cover.
2. New cover dropped right into place. Replaced bin. Everything fit.

took the old piece out, installed the new, replaced the retainer..Done

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Started new gasket soaking in very hot water before removing the old gasket. By the time we were ready to install the new gasket it had mostly regained it's proper shape. New gasket install went smoothly, other than a few of the original clips broke when removing the old gasket.

Wish you gave actual outside measurements of the gaskets so that you don't have to guess the dimensions of ones that are shown overlapping.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

I pryed the old end caps off the bar with pliers being careful not to bend the metal retaining tab on the bar. The new bar end caps snapped right on the bar and the new end caps / bar assembly snapped right into the slot on the door. Very Easy Repair.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I had wasted 5-6 weeks waiting for SEARS to send me the CORRECT Part. They kept sending the wrong part, telling me that the right one would be sent "THE NEXT WEEK" & Then finding out that the CORRECT ONE was on BACK ORDER with NO KNOWN DATE of shipment in Sight! So I looked up the part on the Internet. FOUND PartSelect & THEY found the CORRECT PART(That was on Saturday) with in 3 days... I had the PART! PLUS the Part arrived in GREAT SHAPE-NOT SO WITH SEARS which came with the packaging ALL TORE UP & THE GASKET was half out of the box and BADLY RUMPLED UP! PARTSELECT had very helpful instructions on their site & Over the Phone helped me do it in little or no time at all! I did remove the 2 screws at the bottom or the door-VERY EASY!!! atwhich time I saw that I also needed 2 nylon washers(I had several on hand!) Removing the whole door is not necessary, but in my case I FOUND the very worn washers & Was able to replace them too!... Now the door moves alot easier! PLUS: with the door off, I could do(replace the metal strips)on the Bottom & Inside gasket EASIER!... I WILL NEVER get partsfrom Sears again & ALL of my future Parts Purchases will be from PARTSELECT! I am VERY IMPRESSED & HIGHLY RECOMMEND PARTSELECT!

repalaced the old one with the new one. easy

Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.

I followed the instructions verbatim as others explained. I did it step by step exactly as instructed, The timing was almost exact no more than 30 minutes. I removed the fan the night before the delivery of the new fan and used a small desk fan to cool the compressor. It worked fine in one half hour my freezer read a perfect zero. Thanks for all the help

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

Noticed the fan was not working properly and went online and found out that was the cause. I immediately ordered the part that night at 8:21pm and received the motor and fan blade the next day. I flipped the refrigerator on its side and removed the 3 hex bolts, took off the fan blade first and removed the wires from the motor. I put in the new motor and then added on the new blade and put the 3 hex bolts back on and the wires. The whole process took about 30 minutes. Piece of cake.

per your instructions

First of all, I was very surprised and pleased that I could even locate the replacement part for such a refrigerator I've had for years. The two crisper pan covers arrived the next day (couldn't believe the fast delivery). I proceeded to take the broken crisper covers off and replace them with the two new ones, which fit perfectly. I then slid the crispers into the slots so they could slide in and out. It took me less than five minutes to do. No tools required.