CTX18AJBR Hotpoint Refrigerator - Instructions

Ordered the part from "parts select". Removed old part, installed new part by unscrewing the old switch, simply cutting supply hose ...pluging in the new part and re-attaching water supply line. 10 minutes at most.

i swaped the valve it was very easy, but that did not take care of the proble :(

Replaced single outlet valve for the ice maker

per your instructions

Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple

Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.

repalaced the old one with the new one. easy

Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good

I had to defrost large chunks of ice from the rear of the freezer compartment and tried reactivating the ice maker several times before deciding to order the replacement fill tube grommet and clamp. This was very stressful and complicated to accomplish while trying to avoid food spoilage, and consumed a lot of time. It involved removing the ice maker and various panels, plus disconnection of 2 electrical plugs, then using a hair dryer to melt ice build up. The installation of the new parts was quick and simple once they arrived in the mail, and this appears to have solved the leak problem. The fill tube slides easily into the grommet and the clamp, tightened with a screw driver, secures the water feed line on the other end. Fill tube must be carefully threaded through rear panels and into the ice maker receptacle and the grommet needs to be pushed hard and wiggled in order to seat properly in the rear surface of the refrigerator.

I am a 68 year old woman that had hernia surgery (6) weeks ago so my friend did the replacement. I showed him the video of how to fix it and I felt like I could have done this myself because all you had to do was loosen a couple of screws to get into the back of refrigerator and pull out the bad part. It was like plugging in my cell phone for recharging I do everyday. Unbelievely easily. The price was great also. We priced part locally and they wanted $30.00 and your part was $18.25 plus shipping. Shipping was unbelievely quick also. It was shipped within (2) days after ordering. Very satisfied.

Replaced valve kit and let it run. Took a day for the fill line to thaw and has been making ice like a champ.

I ordered the valve, which came only a day later. Mine is really simple because it only has one water line and one electrical plug in. I do not have a separate water filter. First, I unplugged the refrigerator and shut off the water supply. I unscrewed the cardboard piece from the lower part of the back of the fridge and freed the valve. I pulled out the top water tube that goes from the valve to the top of the fridge, that connects into the back of the ice maker. That tube was empty and dry - I blew through it to make sure that it was unobstructed, and it was. No water was getting to that tube at all. I pulled out the plugs from the valve, and unscrewed the water line from the valve and let that drain in the bucket. I had drained as much water in the lines as I could by flushing a toilet and turning on the sink until it seemed the water supply that was left in the pipes was low. Then I just did the reverse putting together everything with the new valve. I screwed back in the water line that runs from the wall to the fridge. I pushed in the water hose line into the valve until it was all the way in. It was uneven and frayed at the end of that thin hose line, so I cut it very straight across the bottom so it would be entirely flush when it was pushed all the way into the valve. Then I inserted the plug back into the new valve. I put everything back in place, plugged in the fridge and turned on the water supply. I had left the fridge out off the wall so I could check for any leaking. I left it overnight and by morning I had ice! It was so easy. My only difficulty was pulling out the thin water hose from the valve. I did not realize that you can push down on the circular rim and the hose just slips out. I think I saved a lot of money.

water runs in now but still does not make cubes. just keeps dripping until I shut the water off.

With help from this site, It was one of three things. I thought it might be what this site suggested the most common and it was. the valve in back of refrigerator at bottom. Water comming to it, but not getting past. Ordered part. Was here in a few days. Real easy to change out. A few screw / bolts and one wire that fit only one way. I did have to bend new bracket to make it fit. Now have lots of ice cubes!

Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.