CTX18EABQRWW Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Federal Way, AL
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Difficulty in removing the old switch
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Crown Point, IN
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refrigerator light wouldn't come on.
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior Light did not go on due to faulty switch
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Winchester, MA
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Gasket had deteriorated at bottom.
I removed the old gasket and snapped the new one into the grooves. No tools were required.
PartSelect provided excellent service. It was a GE manufactured part. GE no longer stocked this part.
PartSelect is a terrific appliance repair parts vendor.
PartSelect provided excellent service. It was a GE manufactured part. GE no longer stocked this part.
PartSelect is a terrific appliance repair parts vendor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIGIDA from MIAMI, FL
- Parts Used:
- WR2X8474
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Water Leak
Icemaker waterline leaking inside by the grommet where the water line comes in the refrigerator . First removed the water line from grommet . Then removed grommet by hand from the fridge. Last, reversed prodedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Surgoinsville, TN
- Parts Used:
- WR71X10081, WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Freezer Door Bottom Shelf Brackets Broke
Opened the box delivered by FedEx and placed the door shelf retainer bar end caps in the left and right side and inserted the bar.
Whomsoever, put the retainer in when delivered did not secure it and it had always been loose. One day some frozen food got in the way of the door closing and broke my retainers. Thus, I am so happy now that they are very secure and in place as they should have been upon delivery.
I
Whomsoever, put the retainer in when delivered did not secure it and it had always been loose. One day some frozen food got in the way of the door closing and broke my retainers. Thus, I am so happy now that they are very secure and in place as they should have been upon delivery.
I
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly A from Columbus, OH
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap to bar of freezer door broke
Snapped end cap onto bar and installed bar onto freezer door.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from carmel, NY
- Parts Used:
- WR60X123
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not cooling and freezer freezing up
I removed the condenser cover removed old fan blade defrosted the condenser section installed new blade and reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruchik from Bronx, NY
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf retainer bar end cap.
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before ordering. Otherwise, the entire process from order to finish took about 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from CENTRALIA, IL
- Parts Used:
- WR23X37285, WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light kept blinking on and off never same way
turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kaye from San Francisco, CA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from North Quincy, MA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old end cap broke.
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Northglenn, CO
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The above door End Cap broke.
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this instruction helpful to you?
Thank you for voting!