CSX22GABCWW Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Micheal from Longwood, FL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Door dropped on the refrigerator side.
Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from Charlotte, MI
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer door opened too far due to cam being broken.
I had to remove the top hinge of the door and shut off the water supply to the automatic ice maker. I then unhooked the water line and pulled it through the guide as I took the door off. Once the door was off, I removed one bolt with the nut driver and replaced the cam. I reversed the above actions and replaced the door. It is very important to adjust the door so the seal fits tightly and evenly all round the door. It was a relatively simple procedure that went very smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from New Berin, WI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door closing cams on door hinges cracked and sheered off. Door sit low on hinges.
Just watch the Parts Select YouTube videos on replacing the door hinges. That helped a lot.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bowie, MD
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Both Lower Door Cams Worn Through.
Part no. Ps290199 received matched part no. Ordered, which I obtained from your web site, however, part did not exactly match oem part. It was necessary to drill a new top hole in each of the hinges. New hole center was drilled 1/2" off (lower) then hole in supplied part. Jpb could have been accomplished easily by the avg. Homeowner, but the drilling required a little more skill & possible some tools that an average homeowner does not possess. Otherwise job was relatively easy and satisfactorily completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Charlotte, NC
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Door would not shut by itself any longer
The on line "how to" video was PERFECT! I followed the steps and the repair was a breeze. Parts Select is now bookmarked in my favorites! These guys make is SO easy for "non-handy" folks like me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- C huck from East Bethel, MN
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door was not closing properly due to broken closure on hinge
After watching your instruction video and not wanting to shut down refrigerator and remove foods from door, I elected to lift the door and place blocking under it.The actual hinge replacement took approximately 10 mins. I would also like to say that I am extremely satisfied with PartSelects handling of my order and your promptness resending my order because of my goof-up with my own address. I am grateful and will recommend you to anyone who needs parts for any appliance. Thanks again. Chuck Gjovig
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vauleta from Beverly Hills, FL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Broke door stop on fridge.Had to replace cam and hinge
I am a widow, 70 year old. Ordered parts. They came very fast. It took less than Fifteen minutes to remove door and take off broken parts and put the new ones on. I am glad I have two doors on the fridge so I was able to lift it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Elizabethtown, KY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
door would not close by its self
I pulled all the items out of door, removed door top hinge cover, lifted the door off the hinge and removed the bottom hinge and closing cams and replaced them and re hung the door, just about that fast.
PS
Thanks for the parts
PS
Thanks for the parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Stanfield, OR
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Self closing hinge cams wore out and broke
Emptied door shelves and removed top pivot hinge bracket. lifted door of lower pivot and set aside.
Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.
Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.
Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.
Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Southlake, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom door hinge replacement
Part Number: PS290199
1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.
1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Glendale, AZ
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door would not close by itself
Removed two screws from the top hinge, two from the bottom - replace and put back together. It took longer to remove the food from the door than it did to replace it. THANKS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tuttle, OK
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door would not close
I was by myself so I took the entire Fridge door off. Took off the old hinge assembly and installed the new hinge assembly. The process took about 10 minutes and worked like a charm. Door closes like it did 15 years ago.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Blackwood, NJ
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Door would not automaticly close - plastic cam broken
First, I loosened the top hindge bolts about halfway. Then, I took the bolts out ofthe door and then took the door off. Next I took the bottom hindge off and put the new part on. Then, reassembled the door in reverse. However, I didn't tighten the hindges until I made sure to align the door to close properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Wilmore, KY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door had to be pushed to close
The magnetic door strip will hold the door in place if the door shelves are unloaded.I removed the bottom hinge with the socket set and installed the new hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from lesage, WV
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
door stop broke
they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .
Was this instruction helpful to you?
Thank you for voting!