CSK22GABEAD Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brandon from Covington, TN
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Closing Cam Broke
Cake walk repair.
Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, tighten and install cover. tool me 6 minutes.
Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, tighten and install cover. tool me 6 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Grand Haven, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Freezer door would not close,and would pop open if refridge side door would close
After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!!
The new part even came with step by step easy to follow directions.
The new part even came with step by step easy to follow directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorrie from Russellville, AR
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Door dropped. Cam riser was gone
Emptied the refrigerator door so it was easier to take off. Used a screwdriver to remove the screw on the top hinge. Lifted door off bottom hinge. Laid the door down so I could take the bottom hinge off. Removed worn out parts and placed the new one on. Slipped door back on hinge,made sure it would close properly and was lined up with freeze door. Put top hinge back in place. Done!! Now door finally shuts on its own again!!! EASY!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from bayville, NY
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
cam britle door down to metal
remove plastic top hinge cover then twoscrews holding door with door closed it rested against freezer door then lefted off door put on flat surface remove tow screws at bottom of door installed new cam
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rocklin, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door sagged and would not stay closed
Don't even need to empty the shelves in the door.
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.
The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.
The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Waterford, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door closing cam desintegrated
Took the stuff out of the door
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door
You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.
My 7-year-old son helped me - it was a fun father-son project.
Removed the door
Replaced the hinge
Put the door back in
Put the stuff back in the door
You may be thinking that I'm not much for words - but this was SO EASY that it doesn't warrant using more words than I did.
My 7-year-old son helped me - it was a fun father-son project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Colfax, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Hinge assembly spacer at bottom hinge failed breaking up in small pieces
Followed other messages to complete fix. Simple overall.
Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.
Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from Arlington, VA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The Door hinge cam broke apart
Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.
Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.
Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Micheal from Longwood, FL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Door dropped on the refrigerator side.
Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from Charlotte, MI
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer door opened too far due to cam being broken.
I had to remove the top hinge of the door and shut off the water supply to the automatic ice maker. I then unhooked the water line and pulled it through the guide as I took the door off. Once the door was off, I removed one bolt with the nut driver and replaced the cam. I reversed the above actions and replaced the door. It is very important to adjust the door so the seal fits tightly and evenly all round the door. It was a relatively simple procedure that went very smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- henry a from pennsauken, NJ
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
bad door hinge and cam
parts ordered fit perfectly made repair removed items from shelves removed door avd replaced hinges and reassembled 1/2 hour total by myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Woodstock, GA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door would not close properly.
Removed door and replaced bracket assembly. Door works like new. Self closing and sealing properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from hillsboro, NH
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Cam Riser worn out
very easy, thanks for the great selection for parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Davis, CA
- Parts Used:
- WR13X10020, WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken Lower Hinge Cam
Removed food and trays from door. This took longer than the actual repair. Removed top hinge cover (1 phillips screw) and top hinge (2ea 5/16" hex bolts). Removed door, replaced hinge assembly on refrigerator (2ea 5/16" hex bolts)which included a new hinge cam (they don't tell you this, but the cam is included in the assembly so you don't need to order a seperate cam) I now have a spare cam. Piece of cake...your mom could do it!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Clyde Hill, WA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrige not staying shut
I read the details and bought the pair, as directed from other bloggers. I got the hinge piece, followed others advice and had it all done in not time! Saved a lot of money and will use this website again!
Was this instruction helpful to you?
Thank you for voting!