CSX24DLG Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from San Marino, CA
- Parts Used:
- WR2X4901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Door wouldn't close properly
First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Franklinville, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
worn/broken cam , door doesn 't self close
Remove contents of door , Remove top hinge cover - phillips screwdriver , remove top hinge screws ( 2 ) - socket wrench , lift door off lower hinge pin , lay door on edge , remove cam retention screw ( 1 ) - socket wrench , remove broken cam , install new cam , apply vasaline to cam and hinge pins , repeat above steps in reverse . Door now self closes .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CYNTHIA from NEWARK, DE
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Refrigerator door won't close
First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Niverville, NY
- Parts Used:
- WR17X2740
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Blade on auger became stripped
Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from DENVER, CO
- Parts Used:
- 7C7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drum light burned out
removed the bulb from the package unscrewed the old bulb & screwed in the new bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FIFE LAKE, MI
- Parts Used:
- WR30X256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plastic guide in rear of bucket broke it guides auger when dispensing ice
I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodger from Brunswick, OH
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Door wouldn't close with out help.
Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Fountain Valley, CA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The refrigerator door would no stay closed
I was set to buy a new magnetic seal to hold the door closed, when I looked it up on PartSelect I saw the recommendation that the problem might be the door closing cam.. I check it with a mirror and sure enough the cam had broken and the door sagged about 1/4 inch. I then followed the instruction and removed the top hinge, lifted the door off and replaced the cam. I did need two and the one attached to the lower hinge had to be drilled out and a new screw and nut attached to hold the cam. It was simple to do, I would recommend selling the door closing cam be sold in pairs with a #10 1/2 inch long screw with lock nut.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Dallas, TX
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken cam pieces, top and bottom
Removed the top hinge cover held by one screw. Removed the top hinge held by two screws and them lifted the door up and off the bottom hinge. Laid the door on the floor and replaced the cam piece from the kit on the bottome of the door. That required removing one screw and losening another. Removed the lower hinge (two screws) and replaced it with the new one in the kit. The lower hinge includes the other cam piece. Lifted the door onto the lower hinge and then replaced the top hinge and cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLen from Greenfield Twp, PA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken door cam will not close on its own
First i removed the lower cover below doors . Then placed a 4x4 under the door to be fixed to keep it in place. Removed screws from hinge support on unit to remove cam Removed outside screw on door and loosened other to allow other cam to be removed . Always buy two cams if one is broken the other cant be in very good shape .The door will work like new with two .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from PENSACOLA, FL
- Parts Used:
- WR72X209
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken left side slide rail
- Remove drawer and cover being supported by this slide. - Remove front and back screws with the screw driver. - Replace the above removed screws using the new slide. - Replace drawer and cover. DONE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from MALONE, WI
- Parts Used:
- WR72X209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Left side bottom drawer rail (plastic) had broken causing the draw to remain open
I glued the old rail back together twice prior to resorting to ordering the the replacement drawer rail from parts direct. Don't bother glueing the old parts, just buy a new one. Keep the screws from the old drawer rail as new screws are not shipped with the replacement rail. Only took 10 minutes to replace the rail needing only a phillips screwdriver. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from HAZELHURST, WI
- Parts Used:
- 7C7
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light bulb in my freezer door burned out.
Remove the burned out bulb and install the new light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie from Surprise, AZ
- Parts Used:
- 7C7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out.
Screwed new bulb in socket
Was this instruction helpful to you?
Thank you for voting!