CTX18DIBRRAA Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mitchell from Chicago, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The Ice Maker stopped making Ice because the arm over the ice bucket which turned turned on the icemaker was broken
I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from St Louis, MO
- Parts Used:
- WR17X2770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drawr slide broke
followed instructions from video on your site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keven from Fleming Island, FL
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
right side slide rail broken
pull the front cover off, take the two screws out and the side rail comes right off, put the new one in place, put the screws back in and bang!.....all done. Took longer to take the stuff out of the fridge than to make this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Katy, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker not making ice
The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Brownsville, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icemaker does not make ice
I'm a housewife in her late 40's. Before ordering the part, I watched your video on how to remove and install the new icemaker. First I unplugged the refrigerator. After a few minutes, I unplugged the icemaker and unscrewed it. I lifted it a bit and removed it. I did not use the icecup that comes with the part. Instead I removed the one from the old part and inserted it to the new one. Then I plugged in the new icemaker, placed it inside so as to match the holes and screwed it in. YES, it was that simple. It took me less than 10 minutes to do this. I saved myself over $100!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Las Cruces, NM
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no ice
Followed the video, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Edmond, OK
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Maker stopped making ice.
Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from JASPER, GA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was not making ice cubes
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from clinton, TN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
would not make ice
i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Portland, ME
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cord
The adapter made the cord a bit long but other than that it was great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Reading, MA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No ice.
Piece of cake and now I get loads of ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from San Antonio, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice maker not working
unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Owensboro, KY
- Parts Used:
- WR71X10080
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Retainer Bar bend
Removed the bent bar and the end clips. Attached the end clips to the new retainer bar and snapped into place on the refigerator door. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Coto de Caza, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker failed. Easy to diagnose cooling coil was very hot
Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0
Was this instruction helpful to you?
Thank you for voting!