CSX22GABCAA Hotpoint Refrigerator - Instructions

Cake walk repair.

Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, tighten and install cover. tool me 6 minutes.

Removed 2 screws holding top hinge. Removed door. Removed 2 screws that holds the door stop and cam riser replaced cam riser, provided, replaced stop and screws. Removed 2 screws holding lower hinge replaced with hinge, provided, replaced screws. Put door in place and replaced top hinge and srews. Job done

removed door, removed old cracked riser aand replaced with new. You have a easy to follow parts site and very good prices. I will use you for all my future repairs.

I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!

After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!!
The new part even came with step by step easy to follow directions.

Emptied the refrigerator door so it was easier to take off. Used a screwdriver to remove the screw on the top hinge. Lifted door off bottom hinge. Laid the door down so I could take the bottom hinge off. Removed worn out parts and placed the new one on. Slipped door back on hinge,made sure it would close properly and was lined up with freeze door. Put top hinge back in place. Done!! Now door finally shuts on its own again!!! EASY!!!

remove plastic top hinge cover then twoscrews holding door with door closed it rested against freezer door then lefted off door put on flat surface remove tow screws at bottom of door installed new cam

Lifted the door while closed into position even with freezer door. Then put srap pieces of wood under door to hold into place while I removed the old hinge assembly and replaced with the new one. The door works good now. Make sure you replace both peices as they will both be worn.

Followed other messages to complete fix. Simple overall.

Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.

Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.

Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.

First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new lower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.

I could see a broken part but couldn't tell exactly how it was oriented on the hinge. I bought just the cam riser but then thought I needed the hinge kit based on what I read on this site. Then I saw better pictures of the hinge kit on another site & realized there are 2 cam risers that meet. The one riveted to the hinge was fine (in my case) - I only needed the upper one...a very inexpensive repair. Do NOT remove the door for this repair. Slide the door up a bit while closed and use a pint-sized paint can to prop it up. Make the repair and remove the can...done.

Removed guards and covers, (2 snap connections, 3 phillips head screws) Removed two 5/16" screws, removed door, removed cam from bottom of door, installed new items.

Worked Great!!!

Just remove all items in door shelves, remove screw holding top hinge cover on. Remove two bolts holding top hinge and remove hinge from door. Carefully open door and lift out of bottom hinge. Remove screw holding bottom hinge on door and replace broking cam riser. Reinstall door in reverse order and adjust top hinge where both doors are even across the top. Thats it!!!!!