HTS22CBMARWW Hotpoint Refrigerator - Instructions

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I removed the top vent and unplugged the ice machine ,took the back cover off the freezer.Removed the old fan which was pretty easy(unplugged it after I took the housing out for easy access) I plugged the new fan in and put everything back in the order I took off, and yada yada yada we have cooling.

You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.

Removed the old control board at the rear of the refigerator, installed the replacement board.

Disconnected power, removed screws from cover on back of refrigerator, unpluged wire connectors, squezzed four support fasteners and removed old board. Put new board on support fasteners, reconnected wiring, replaced cover, pluged power back in, turned controls back on. It wored fine.

narrowed it down to the circuit board...removed cover panel after unplugging frig. read directions thouroughly.... removed cables attached to old board. this is the tricky part removing the board from the plastic clips....broke two pulling old board off popped new Board onto remaining plastic mounting clips and reattached cables plugged frig in and got a shock as my shoulder touched the board. everything seemed to be working and but cover back on....viola all done.

I followed instructions in your video. at the beggining I hesitated because the original card had two fewer ports than the new one. but after a call to a Partselect representative I confirm that I had the right card. after that it was a matter of connet wires to the ports. 1 week later my refrigerator is running smooth. Thaks a to Partselect I have saved a bunch of money.

Received main board in less than two days. back of frig. small panel removed 3 screws, removed cover exposing main board with needle plires squeesed 4 plastic tips to release board unpluged conectors, reinstaled new board, worked perfict. Thank you for your helpfull web site. Bob.

Disconnected power at outlet. Removed three screws from access panel. Disconnected six electrical connections, compressed three plastic retaining pins and removed board. Installed new board and reconnected connections, installed three screws on access panel and turned the fridge on. No more crazy evaporator motor noise

diagnosis, fan would run more than normal, compressor would only come on sometimes, check line voltage to the mother board (yes !!! a mother board with a relay for the compressor built onto it )! check the switched voltage out to the compressor. If a/c 115 in but no a/c 115 out while the fan is on replace the mother board. Remember this is a LIVE VOLTAGE TEST, BE CAREFUL HOW AND WHAT YOU TOUCH YOUR LIFE IS NOT WORTH SAVING A REPAIR BILL !!!
I suppose if if went long enough in this condition the result would be fan runs a lot but it does not get cold.
Hope this helps
God Bless
Captain Scott Cousins

I used a steak knife and pried the broken piece off, lined up the plastic pins, gently tapped them down (with the knife handle) and stepped back and admired my work.

You web site made it easy to see I was ording the correct part. No guessing, ordering, returning and reordering to get the right part.

Thank You
Barb Anderson

After determining it was not a problem with the defrost cycle, ( this refrigerator had no separate defrost timer), I ordered the main circuit board with the hope that the relays built into it were hanging up and not properly turning on the compressor, (a chattering sound could be heard). Ten screws to take the access cover to the board off and a few connectors later and it was as good as new. Took about ten minutes!

Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.

This was generally an easy fix. The work was in such a confined area of our side by side and my husbands shoulders are broad so that was a little more challenging but overall a quick, easy and cheap repair doing it ourselves without having to call a appliance repairman.

After turning off power and unthawing back cover so I could remove it. Then I had remove all of the ice from the coils with a hair dryer. After everything was unthawed I removed the temperature sensor from the coil tubing and cut the wires. I skinned the wires on the new sensor and crimped a butt splice on each wire. I skinned each wire in the freezer then crimped butt splices to each wire. After taping the connections with black tape I reinstalled the back cover and turned on the power. So far it has been two weeks and there Is no frost and the refridgerator is working fine.