CSX20BABGWH Hotpoint Refrigerator - Instructions

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

First I removed glass shelf on top of rail. I then removed the two screws holding rail to refrigerator side. Next I installed new rail using same two screws. Finally I replaced glass shelf on top of rail.

took 2 philips screws out,took off rail,and then nreverse.these steps,

Removed 2 screws replaced new part very easy

When the part first arrived I thought that I had ordered the wrong one. It was a dual element heater while the one in the freezer was a single. After reading the instructions it gave specific info on how to replace a single element with the dual. It was VERY easy to replace. i had manually defrosted the coils a couple of days before but they were already covered in frost. I know that I should have manually defrosted them again but I installed the new element anyway and it started working instantly (must have caught it on the 'on' cycle or when I repowered the fridge it started the 'on' cycle). The coils were defrosted within a few minutes. Amazing. Very easy to follow instructions.

Considering that I am a woman who knows nothing about repairing or let alone anything about refridgerator parts etc.... It was very easy.

First I went on line to see if I could even figure out what may be the problem with my refridgerator. After hearing similar stories on this site I thought I would try to order a new heating element since it wasn't that expensive and hopefully save me lots in $$$ have a repair man come out.
I removed the shelves in the freezer portion and then removed the back panel. I had to wait for the freezer to defrost, then I removed the burned out heating element which is about 10 inches long and replaced it with a new one.
It was so simple and probably would have taken less time if I had the freezer already defrosted.
Now the refrigerator is working like new and I fixed it all by myself without the help of my husband!!!!

Removed panel, then removed single coil unit and replaced it with double coil unit that was sent to me. Refrigerator now working fine.

This fridge had this same problem 4 other times, each time about 1 yr apart. Being as I considered myself ''mechanically challenged'' my wife always contacted her favorite appliance repair man. However, he was unavailable, so wife was gearing up to go ahead, bite the bullet, and buy a new fridge. We really didn't want another bill to worry with so she suggested I try the repair myself. She'd watched the repairman do it the last couple of times and ensured me it would be ''a piece of cake'' plus save us some bucks and put off an added expense at least a little longer. Ordering the part from this site was simple. The fridge did have the old 1 bulb element and the new one was the 2 bulb element so I was afraid I'd have to do some splicing, but lucked out and the wire was easily redirected and reached without any stress or problems to plug into the new part. She watched the install video and was able to talk me through it without any problems. We saved at least $125 install bill, plus put off making a big item purchase a while longer. I hope the new 2 element defroster does a better job and we might just get 10 more years out of 'old faithful'!

Parts select sugested checking the freezer side on the side by side if there was frost on the back panel. I took the back panel off on the freezer side inside the freezer. I found that the freezer coils were full of ice.Had to use a hair dryer to melt all the ice. The heater element was bad on the bottom of the freezer. I ordered a new defrost element an installed in 40 minutes and is running fine.You can still use the refrigerator until the new part comes in if you melt off the coils.It will last about 2 weeks.

Followed the video describing the repain and the written directions. The Video is excellent and made the job easy to follow

This is a repair INSIDE the freezer. Turned off unit.. Unplugged. Removed shelving on freezer side. Removed freezer draw rails (4 screws total.) Removed 2 screws that hold rear panel in place at rear of freezer side (this is inside the freezer). Carefully removed metal panel by pulling from the left (side that does not have shelving clips. As noted on this website and other users, the freezer coils were incased in ice. Thawed with a hair dryer (put towels in bottom of freezer-ice was pretty heavy in mine). When thawed, remove heater element by removing 2 screws that hold it to the aluminum bracket. Then remove wires on each end. Simply install the new emelment by attaching wires back on heater and screw new unit in place. (My original heating element was a single element-you could very easily see where the heating coil inside the glass tube had shorted out. My replacement heater was a 2 element unit. This did not pose any problem at all-installs in the same manner-good directions are provided.). Replace all parts in reverse order. It's that simple. Saved probably $150. This site is wonderful! Fast shipping and the users install tips/notes are fantastic!! Will shop here again if I have to (have a Maytag washer that isn't draining and going into spin-bet the fix is on here somewhere!

Fortunately while my refirgerator was still under warrant I had this same problem and watched the repairman fix it. To confrm my suspicions I cleaned out the freezer compartment, removed the back panel (2 screws), and used a hair dryer to defrost it. I suggest plugging the drain hole or laying a towel in the bottom of the compartment to catch the run off or your drain pan could over low. Once defrosted I was able to verify that the element on the defrost heater was burnt. Since it was Sunday I re-assembled and cranked it back up until I could get the part. I did a goggle search on Monday, found the part instantly using only the model number from the refrigerator at PartsSelect.com. The part arrived Wednesday as promised, I repeated the process from Sunday, removed the defective part (2 screws & 2 plug in type wire connections) and she works like a charm now. I do think the manufacture of the part should consider a new design since this is the second one my unit has needed in less than 5 years. At only $27.50 ea. I should have purchased a spare to have for the next time!

I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair

I removed the drawer and glass shelf, removed 2 screws and replaced with new drawer slide in reverse order. I removed the contents of the door, the top hinge, and then laid the door down. On the bottom of the door, I replaced the pivot piece (provided) and then I replaced the hinge on the lower right side of the refrigerator box (2 screws with a nut driver bit). I now reversed the order to re-assemble the door and finally re-aligned the top hinge to adjust the door fit. Less than 30 minutes total. EASY!

First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repair took much less time than I anticipated.