CTS18FBSDRWW Hotpoint Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marlys from HAINES CITY, FL
- Parts Used:
- WR17X11662
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Was broke on side
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Eugene, OR
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leland from HERMISTON, OR
- Parts Used:
- WR24X10228
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Hard to get started at the corners because it was hard to see the slot.
My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along.
That helped us finish the installation.
Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.
That helped us finish the installation.
Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Sylva, NC
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from Fort Myers, FL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
light in freezer section not working
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juaneese from Madison, TN
- Parts Used:
- WR17X11662
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Broken Vegetable Pan Cover
I replaced the Vegetable Pan Cover myself and it looks and fits great. The hardest job was unloading so that the previous cover could be taken out. I was proud of myself for being able to do this job myself without any help. Ordering and receiving the part was so easy that I will always use Parts Select. Thanks again. Juaneese
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from Laurel, MD
- Parts Used:
- WR24X10228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement gasket
I took it right out of the framed box to keep the gasket in shape and snapped it back on the gasket mount on the freezer door it took 5 minutes or less perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MAE from FARMERS BRANCH, TX
- Parts Used:
- WR24X10236, WR24X10228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The old gaskets were not sealing properly.
removed the old gaskets with the putty knife to pry it loose then pulled the old gaskets off. Soaked the new gaskets in slightly boiling water to make them better able to straighten out and then installed by lining them up and pressing them in place, making sure they were lined up and that they were in the track provided for them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reese from Coconut Creek, FL
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
defrost timer was bad
repalaced the old one with the new one. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- r from Bronx, NY
- Parts Used:
- WR24X10236, WR24X10228
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Gaskets needed replacement to maintain correct temperature in the refrigerator and freezer
Removing the old gaskets was very simple. Replacing the fresh door gasket was the most time consuming. It would have been easier if I had help, it took a some time and patience. The gasket works perfectly. The freezer gasket was easy to replace. The gaskets fit perfectly, thank you. For the ladies out there, you if I can do it, so can you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from West Seneca, NY
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Frezzer would freeze up, refrigerator stayed cold, solved the problem. Now the refrigerator seems to be running more than usual.
Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KIRK from Malibu, CA
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Freezer work refierator compartment is warm
Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- N Smith from Chicago, IL
- Parts Used:
- WR24X10236
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
replaced the refrigerator door gasket
The original gasket had ripped and the magnet strip was hanging out. Following information from several youtube video clips & suggestion from the seller, I soaked the gasket in a tub of hot water for 30min to make it more pliable. After removing the old gasket, I put on the new, which only appeared to just snap into a metal tract. However the door couldn't seal. There were big gaps. That is when I realized that the gasket was still rigid. So I took a heat gun and carefully blew hot air on the gasket as I pulled it out enough for the metal edge of the gasket to attach itself to the refrigerator. Took quite a while to get it to seal correctly, but seems to be working well now.
Was this instruction helpful to you?
Thank you for voting!