CSX27DRXFWW Hotpoint Refrigerator - Instructions

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Pull out the old, dump the nasty ice. Remove 4 screws attached to the front cover. throw in trash, replace with new auger assembly, with 4 screws. Put it back in ice maker and let it make ice. Easy, cheap and never left the house to searc for the right part, found it on the front porch.

Removed the Ice Maker container. Removed the one screw that held the remnant of the old light shield. Placed the new light shield in place and installed the screw. 5 Minutes from start to finish.

SNAPPED THE NEW SHIELD IN PLACE. DONE!

replaced lights in refrigirator and freezer

Removed the old assembly from the refrigerator. Used a screwdriver to remove the four screws attaching the old assembly to the plastic front plates. Opened the box holding the new part (which had arrived very promptly at our doorstep), removed it and attached it very easily to the plastic front plates using the same four screws. Placed the new assembly in the refrigerator and started making new ice. It was EASY!! We had read what others had said about this repair and knew it would be something we could do. Your website is very user friendly and helpful.

Disassembled ice-maker, noting what screws went where, what direction ice release control arm pointed, and noting how the control arm spring was mounted. The door assembly comes off first followed by the circular assembly that houses the ice door and last grinding arms. It is quite easy see how it comes apart as you look at the screws. Remove the screw holding the back end of the control arm and note the spring position. The control arm needs to be turned to line up notches to pull it thru a faceplate hole while rotating the arm about the "U" that is on the outside of the faceplate in the door housing. There is a retaining clip holding the rotating impeller to remove to complete the dis-assembly. Use vinegar to clean rust out of bin and other parts around the faceplate. Assemble the unit in the reverse order to complete the job.

Removed old ice bucket with auger. Unscrewed front plates that form the front of the ice bucket. Replaced the front plates on the new part (ice bucket and auger). Replaced new assemblage. It took about 20 minutes. Had to empty ice out and put in a temporary cooler for storage. Bigger problem than the repair was diagnosing what was wrong. Pushed disagnose button and it said ice maker was working normallly. Careful examination of the ice bucket removed from refrigerator showed spring out of place on long metal rod that protrudes from the back of the ice bucket and fits into a square hole in back of refrigerator. Examined other end of rod that engages with plastic parts that run the ice auger and ice crusher mechanism. A piece must have broken off. That was the problem. Refrigerator ice maker now works fine as originally designed. Push crudh the ice crusher engages and you get crused ice. Push cubes and the icemaker crusher slides out of the way and you get cubes.

This is the easiest thing in the world - thanks for sharing other's installation - it took 5 mins - works perfect & we have clean ice - 4 easy screws to remove - anyone can do it!

I removed the ice maker,removed the broken piece of the old light shield,screwed the new light shield in place,and replaced the ice maker.It took all of 5 minutes.

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.

The light shield is only held in with a single screw, so it was the simplest install ever - unscrew the old light shield (in my case, the remaining piece of the light shield), put the new shield in place, and screw it down. Doesn't get any easier than that.

i ordered this ice maker on sunday night and paid for the cheapest shipping. it got here monday morning and i couldnt believe it. super fast shipping!! works great

Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screws that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.